Carver 42 SUPER SPORT Скачать руководство пользователя

Страница: 80 / 141

4127 • 42 Super Sport 4/06

INTERNAL SYSTEMS

SECTION 4

6. After all grey water is pumped overboard, turn the waste pump switch “OFF.”

7. Remove the grey water tank deck plate labeled “WASTE” using the removal

tool supplied with your boat. This plate is located in the cockpit on the

forward port weatherboard. Refer to Section 9 - Deck Plates for the exact

location of this plate.

8. Flush the grey water tank by pouring a few gallons of fresh water through the

“WASTE” deck ﬁtting. Reactivate the overboard discharge pump and remove

the fresh water and any remaining grey water, then turn the pump “OFF.”

9. Replace the “WASTE” deck plate.

10. Close the overboard discharge seacock.

11. On the DC Control Center, switch the Grey Water Pump circuit

breaker “OFF.”

Содержание 42 SUPER SPORT














































































































































Результаты поиска

Содержание 42 SUPER SPORT

Отзывы:

Похожие инструкции для 42 SUPER SPORT

Бренды по названию

Популярные бренды

Carver 42 SUPER SPORT, Руководство пользователя

Результаты поиска

Содержание 42 SUPER SPORT

Отзывы:

Похожие инструкции для 42 SUPER SPORT

Бренды по названию

Популярные бренды