CARLO GAVAZZI Carpark 3 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 80

CARLO GAVAZZI Carpark 3 Скачать руководство пользователя страница 69

CP3 version 3003

69

MZC combined with the Single-Space System

The MZC can easily be combined with the single-space detection system. Using the same configuration tool
and the same carpark software (SBP2CPY24) as for the single-space system, installers can easily combine an
MZC system and a single-space system.

The counting system uses a different sensor (SBPSUSCNT) intended for counting, and the single-space
system uses either a lane-mounted sensor or a vertical sensor for detection of cars in a parking space. The
additional modules used are identical for both systems. Assignment and calibration in the configuration
tool are equal for all sensor types used in Carpark 3. The significant difference between single-space and
MZC lies in the configuration part. The design in the SBP2CPY24 is more or less equal to the single-space
system. Please refer to the ‘Software Installation Manual’. The software installation manual is available
here:

http://www.productselection.net/MANUALS/UK/cp3_manual.pdf

Single-space detection and counting system combined

«
...
67
68
69
70
71
...
»

Содержание Carpark 3

















































































Отзывы:

Нет отзывов