CARLO GAVAZZI Carpark 3 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 80

CARLO GAVAZZI Carpark 3 Скачать руководство пользователя страница 21

CP3 version 3003

21

The carpark sensor consists of two parts: the sensor itself and a base holder to be mounted on the ceiling,
cable tray or installation box. The sensor has a small cable with a male RJ12 connector that must be
plugged into the female RJ 12 connector in the base part. The sensor is detachable from the base, which
makes replacement of the sensor easy. Once the sensor is locked to its holder, it is secured by a safety lock.
The sensor is not delivered with the base. The base must be ordered separately.

LED Indicator

LED indicator with eight colours built in (red, green, amber, yellow, light-blue, blue, purple and white),
Dupline® bus powered

SBPILED

The LED indicator consists of three bright RGB diodes implemented in a housing of transparent
polycarbonate. It uses the same base holder as the sensors. The LED indicator has a small cable with a male
RJ12 connector that must be plugged into the female RJ12 connector on the base part. LED indicator is not
delivered with a base module. The base must be ordered separately.

LED indicator

Base A and Base B

Base A, low base with SIN number

SBPBASEA

Base B, tall base with SIN number

SBPBASEB

Base A is a low base used for rail mounting. The cable is inserted from the top of the base and the
knockouts are used for mounting in the rail.

Base B is a tall base used for mounting on the ceiling. The knockouts on the side of the base are for pipes
with the 3-wire cables.

Both base types can be used together with all Carpark 3 sensors or LED indicators. The base has a 2*3-wire
connection for d+, d- and POW. The base also has a female RJ12 connector, which must be connected to
the sensor or LED indicator. Moreover, it has a PCB containing the unique SIN number for identification
when connected to the Dupline® bus.

«
...
19
20
21
22
23
...
»

Содержание Carpark 3

















































































Отзывы:

Нет отзывов