
■ CLEANING
COPIER (Service mode for printer) > OPTION (Specification setting mode) > CLEANING
OHP-PTH
2
Set of ITB clean transp threshold value
Detail
To set the number of sheets as the intervals to execute ITB cleaning when feeding transparency.
When a large number of transparencies is fed, surface active agent adheres to the ITB, and
consequently the transfer efficiency is lowered, causing an image failure. Normally, a solid single
Bk-color patch with 80 mm width is formed on the ITB, and surface active agent is removed together
with the toner every time after feeding 10 sheets at paper interval and 5 sheets at last rotation.
As the value is changed by 1, the number of sheets at paper interval and last rotation is changed
by 1 sheet.
When the value is decreased in the case of using transparency to which surface active agent is
more likely to be adhered, image failure can be alleviated.
When the value is increased, downtime and toner consumption can be reduced, but image failure
may occur.
Use Case
When an image failure occurs due to decrease in the transfer efficiency
Adj/Set/Operate Method
Enter the setting value (switch negative/positive by -/+ key) and press OK key.
Display/Adj/Set Range
-10 to 10
Unit
sheet
Default Value
0
Amount of Change per
Unit
1
ITB-CL-L
2
Set toner band length: ITB Clean Blade
Detail
To set the length of toner band for preventing flipping of the ITB Cleaning Blade.
Increase the value when noise comes from the ITB due to the flipping. If the length of toner band
gets longer, flipping can be prevented, but toner consumption is increased.
When 0 is set, toner band is not formed.
Use Case
- When noise comes from the ITB
- When low productivity or high toner consumption is pointed out by the user
Adj/Set/Operate Method
Enter the setting value, and then press OK key.
Caution
Do not use this when the machine is operating correctly.
Display/Adj/Set Range
0 to 100
0: OFF, 1: 1 mm, 2: 2 mm, ..., 100: 100 mm
Unit
mm
Default Value
1
Related Service Mode
COPIER> OPTION> CLEANING> ITB-CL-T
Amount of Change per
Unit
1
ITB-CL-T
2
Set toner band form intvl: ITB Cln Blade
Detail
To set the interval to form toner band for preventing flipping of the ITB Cleaning Blade.
The interval is determined by entering the amount of increase/decrease (sheet) compared to the
specified number of fed sheets.
Decrease the value when noise comes from the ITB due to the flipping. If the interval to form toner
band is decreased, flipping can be prevented, but toner consumption is increased.
Use Case
- When noise comes from the ITB
- When low productivity or high toner consumption is pointed out by the user
Adj/Set/Operate Method
Enter the setting value (switch negative/positive by -/+ key) and press OK key.
Caution
Do not use this when the machine is operating correctly.
Display/Adj/Set Range
-10 to 10
Unit
sheet
Default Value
0
Related Service Mode
COPIER> OPTION> CLEANING> ITB-CL-L
8. Service Mode
782
Содержание imageRUNNER ADVANCE C3500 III Series
