California Instruments 12000L-1P Скачать руководство пользователя страница 2

Страница: 2 / 151

INSTRUCTIONAL MANUAL

2750L-P/4500L-P/6000L-P

August, 2001

Rev. K

-ii-

TABLE OF CONTENTS

SECTION 1

INTRODUCTION AND SPECIFICATIONS ---------------------------------------------------------------------- 1

1.1

INTRODUCTION-------------------------------------------------------------------------------------------------------------- 1

1.2

GENERAL DESCRIPTION ------------------------------------------------------------------------------------------------- 1

1.3

ACCESSORY EQUIPMENT/RACK SLIDES --------------------------------------------------------------------------- 3

1.4

SPECIFICATIONS------------------------------------------------------------------------------------------------------------ 3

SECTION 2

INSTALLATION AND ACCEPTANCE ------------------------------------------------------------------------- 13

2.1

UNPACKING ----------------------------------------------------------------------------------------------------------------- 13

2.2

POWER REQUIREMENTS----------------------------------------------------------------------------------------------- 13

2.3

MECHANICAL INSTALLATION ----------------------------------------------------------------------------------------- 13

2.4

INPUT WIRING-------------------------------------------------------------------------------------------------------------- 13

2.5

OUTPUT CONNECTIONS------------------------------------------------------------------------------------------------ 20

2.6

OUTPUT VOLTAGE RANGES ------------------------------------------------------------------------------------------ 20

2.7

FUNCTION TEST----------------------------------------------------------------------------------------------------------- 20

2.8

REAR PANEL DIP SWITCH (SW1) ------------------------------------------------------------------------------------ 21

SECTION 3

OPERATION ---------------------------------------------------------------------------------------------------------- 24

3.1

GENERAL -------------------------------------------------------------------------------------------------------------------- 24

3.2

FRONT PANEL CONTROLS -------------------------------------------------------------------------------------------- 24

3.3

FRONT PANEL INDICATORS------------------------------------------------------------------------------------------- 24

3.4

REAR PANEL CONNECTIONS ----------------------------------------------------------------------------------------- 26

3.5

FRONT PANEL PROGRAMMING-------------------------------------------------------------------------------------- 31

3.6

TO MEASURE THE OUTPUT ------------------------------------------------------------------------------------------- 46

3.7

REMOTE PROGRAMMING WITH ABBREVIATED PLAIN ENGLISH (APE)-------------------------------- 47

3.8

REMOTE OPERATION WITH MATE CIIL---------------------------------------------------------------------------- 67

SECTION 4

CALIBRATION PROCEDURE ------------------------------------------------------------------------------------ 82

4.1

GENERAL -------------------------------------------------------------------------------------------------------------------- 82

4.2

TEST EQUIPMENT--------------------------------------------------------------------------------------------------------- 83

4.3

PERIODIC CALIBRATION------------------------------------------------------------------------------------------------ 88

4.4

NONPERIODIC CALIBRATION ----------------------------------------------------------------------------------------- 96

SECTION 5

THEORY OF OPERATION ---------------------------------------------------------------------------------------105

5.1

GENERAL -------------------------------------------------------------------------------------------------------------------105

5.2

OVERALL DESCRIPTION-----------------------------------------------------------------------------------------------105

5.3

INPUT POWER SUPPLY ------------------------------------------------------------------------------------------------105

5.4

AUXILIARY POWER SUPPLY -----------------------------------------------------------------------------------------107

5.5

CURRENT LIMIT BOARD -----------------------------------------------------------------------------------------------107

5.6

INDICATOR BOARD------------------------------------------------------------------------------------------------------107

5.7

RANGE RELAY BOARD -------------------------------------------------------------------------------------------------107

5.8

AMPLIFIER MODULES --------------------------------------------------------------------------------------------------107

5.9

OSCILLATOR MODULE -------------------------------------------------------------------------------------------------108

5.10

CPU/GPIB BOARD --------------------------------------------------------------------------------------------------------108

5.11

PHASE A/REF BOARD---------------------------------------------------------------------------------------------------109

5.12

PHASE B/C BOARD ------------------------------------------------------------------------------------------------------109

5.13

DISPLAY MODULE -------------------------------------------------------------------------------------------------------109

SECTION 6

MAINTENANCE AND TROUBLESHOOTING---------------------------------------------------------------111

6.1

GENERAL -------------------------------------------------------------------------------------------------------------------111

6.2

POOR VOLTAGE ACCURACY ----------------------------------------------------------------------------------------111

6.3

POOR OUTPUT VOLTAGE REGULATION-------------------------------------------------------------------------111

6.4

OVERTEMPERATURE LAMP ON-------------------------------------------------------------------------------------111

6.5

OVERLOAD LAMP ON ---------------------------------------------------------------------------------------------------112

6.6

CAN'T PROGRAM AC POWER SYSTEM ON GPIB -------------------------------------------------------------112

6.7

DISTORTED OUTPUT ---------------------------------------------------------------------------------------------------112

Содержание 12000L-1P























































































































































Результаты поиска

Содержание 12000L-1P

Отзывы:

Похожие инструкции для 12000L-1P

Бренды по названию

Популярные бренды

California Instruments 12000L-1P, Инструкция по эксплуатации

Результаты поиска

Содержание 12000L-1P

Отзывы:

Похожие инструкции для 12000L-1P

Бренды по названию

Популярные бренды