California Instruments 12000L-1P Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 151

background image

INSTRUCTIONAL MANUAL

2750L-P/4500L-P/6000L-P

August, 2001

Rev. K

-78-

SYNI may be used with PANG to program the phase A phase angle relative to the sync signal. The following string
enables the power source to track the frequency and phase of the external sync signal:

FNC ACS :CH00 SET SYNI <CR> <LF>

Note that other noun modifiers may be included in the above string.

While operating in the external synchronize mode, the power source tracks the frequency and phase of the external
signal. Note that its phase may be offset from the SYNC input (see paragraph 3.8.4.3). The frequency of the external
signal is reported with the following set of strings:

(L) FNC ACS FREQ :CH00 <CR> <LF>

(L) INX FREQ <CR> <LF>

(T) <SP> "default time-out value reported"<CR><LF>

(L) FTH FREQ <CR><LF>

(T) <SP> "measured value of external sync frequency reported" <CR> <LF>

In the above, (L) indicates the power source is listen addressed and (T) that it is talk addressed. The INX OP-code in
the above series of strings may be omitted if the time data is not required.

3.8.4.6 CURR

The CURR (current measurement) noun modifier's single function is to measure current. The strings to initiate the
current measurement of Phase B are as follows:

FNC ACS CURR :CH02 <CR> <LF>

FTH CURR <CR> <LF>

The current of Phase A, B or C can be measured with channel designators :CH01, :CH02 or :CH03, respectively.

3.8.4.7 POWR

Noun modifier POWR (power measurement) is included in a string to instruct the power source to measure the power
output of the power source. The strings to initiate the power measurement are as follows:

FNC ACS POWR :CH01 <CR> <LF>

FTH POWR <CR> <LF>

The response from the power source is:

<SP> 80.5 <CR> <LF>

The foregoing assumes an output power on phase A of 80.5 watts. The power of either Phase A, B or C may be
measured.

3.8.4.8 APOW

Noun modifier APOW (apparent power measurement) included in a string instructs the power source to measure the
apparent power output of the power source in volt-amperes (VA). The strings to initiate the measurement are as
follows:

FNC ACS APOW :CH01 <CR> <LF>

FTH APOW <CR> <LF>

The response from the power source is:

«
...
80
81
82
83
84
...
»

Содержание 12000L-1P
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000L-1P

Бренд: Gallagher Страницы: 104

POWERFIX KH4055

Бренд: Powerfix Страницы: 4

Бренд: TDK-Lambda Страницы: 31

Бренд: Hama Страницы: 56

Protege PRT-PSU-DIN-8A

Бренд: ICT Страницы: 36

Бренд: Laguna Tools Страницы: 23

Бренд: Cantek Страницы: 29

Бренд: SilverBolt Страницы: 9

Бренд: Hach Страницы: 32

Бренд: Galaxy Страницы: 11

PSI 8000 3U HS PV Series

Бренд: Elektro-Automatik Страницы: 76

Бренд: patura Страницы: 32

Бренд: Parkside Страницы: 184

Wireless Power Supply RS24E-424N-PU Series

Бренд: B&PLUS Страницы: 2

Бренд: Parkside Страницы: 44

Бренд: Parkside Страницы: 79

12V Power Packs

Бренд: Draper Страницы: 12

Бренд: Delta Electronika Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды