California Instruments 12000L-1P Скачать руководство пользователя страница 48

Страница: 48 / 151

INSTRUCTIONAL MANUAL

2750L-P/4500L-P/6000L-P

August, 2001

Rev. K

-44-

ERROR MESSAGE

CAUSE

CRL FAULT

Indicate output current exceeds program current.

AMP (1) FAULT

Incorrect sense line connection. Overload on indicated output.

TEMP (1) FAULT

Amplifier overtemperature

CPU MEMORY FAULT

CPU failed self-test

DMA OVERFLOW

Remote message greater than 256 bytes.

EXT SYNC ERROR

No external sync input at System Interface connector. Signal is not between 45 and 2
or 5 KHz.

BUS LOCAL ERROR

Remote message sent while AC Power System is in local.

SYNTAX ERROR

Incorrect syntax received from IEEE-488 External Interface

AMP RANGE ERROR

Attempt to program AMP value greater than RNG value.

FRQ RANGE ERROR

Attempt to program FRQ less than 45 (2) or greater than 2 or 5 KHz.

PHZ RANGE ERROR

Attempt to program PHZ greater than ±999.9

CRL RANGE ERROR

Attempt to program CRL greater than 11.11 or 33.33.

RNG RANGE ERROR

Attempt to program RNG greater than 270.0 or other optional high voltage range.

RMPA RANGE ERROR

Attempt to program STP, DLY or VAL greater than the maximum.

DIV

ERROR

Consult

factory.

OVERFLOW ERROR

Consult factory.

_________________________________________________________________

(1) May be any combination of A, B or C.

(2) May be down to 17 Hz with reduced output voltage.

Table 3-9

FRONT PANEL DISPLAY ERROR MESSAGES

Содержание 12000L-1P























































































































































Результаты поиска

Содержание 12000L-1P

Отзывы:

Похожие инструкции для 12000L-1P

Бренды по названию

Популярные бренды

California Instruments 12000L-1P, Инструкция по эксплуатации

Результаты поиска

Содержание 12000L-1P

Отзывы:

Похожие инструкции для 12000L-1P

Бренды по названию

Популярные бренды