background image

INSTRUCTIONAL MANUAL 

 

2750L-P/4500L-P/6000L-P 

August, 2001 

 

 

Rev. K 

-113- 

 

2.  

The crest factor of the load current exceeds 2.5.  With this condition the distortion will be much higher 
at frequencies above 100 Hz. 

 
  

 

SOLUTION:   

Reduce the load or program the current limit to a higher value. 

 

6.8 NO 

OUTPUT 

 
If the AC Power System has no output at the rear panel terminal block, TB1, the following items may be at fault: 

 

 

 

1.  

If the External Sense lines are not connected correctly, there will be no output.  The error message 
AMP FAULT will also be generated. 

 
  

 

SOLUTION:     Correctly connect the sense lines.  Refer to Paragraph 2.5. page 20

 
 

2.  

When the output is overloaded an error message will be generated and the output relays will open.  
The error message would be AMP FAULT. 

 
  

 

SOLUTION:    Remove the overload.  Observe the output power capabilities.  Refer to Section 1, 
page 1

 
 

3.  

There is no input to the power amplifiers from the oscillator.  Check the oscillator signals at the system 
interface connector: 

 
  

 

 

J7-24    Oscillator Phase A 

 

   J7-6 

Oscillator 

Phase 

  

 

 

J7-23    Oscillator Phase C 

 

   J7-7 

Oscillator 

common/return 

 
  

 

Program 135.0 volts on the 135 volt range.  The three signals should be 5.0 ±0.10 VAC. 

 
 

 

SOLUTION:   

If there is no signal at the Systems Interface connector replace the oscillator.  Refer to 
paragraph 6.9. page 113. 

 
 

 

SOLUTION:    If the signal at the System Interface connector is greater than 5.0 VAC, it may be 

necessary to replace the respective amplifier.  Refer to paragraph 6.11. page 114. 

 
 

4.  

One of the internal fuses, F1, F2 or F3 has failed. 

 
  

 

SOLUTION:    Replace the fuse.  Remove the input power and discharge capacitor C1 before 

replacing  the fuse.  Refer to paragraph 6.11. page 114

6.9 MODULE 

REMOVAL 

 
Figure 6-1 shows the location of the internal modules and assemblies.  The figure shows the Amplifier Modules, A1, A2 
and A3, with the insulator removed. 
 

6.10 

OSCILLATOR MODULE REMOVAL/REPLACEMENT 

 
If a fault is found that requires the replacement of the Oscillator Module (assembly 4009-425) perform the following 
steps and refer to Figure 6-1 for the module locations: 
 
 

1. 

Turn off the front panel circuit breaker. 

 
 

2.  

Remove the power system's top cover. 

 

Содержание 12000L-1P
























































































































































Отзывы: