manualshive.com logo in svg

California Instruments 12000L-1P, Инструкция по эксплуатации

Инструкция по эксплуатации California Instruments 12000L-1P доступна для бесплатного скачивания с нашего сайта. Этот мощный и надежный источник переменного напряжения имеет широкий спектр применения. Скачайте бесплатно руководство по эксплуатации с нашего сайта manualshive.com прямо сейчас, чтобы использовать все возможности этого устройства.

Поделиться
Скачать
background image

INSTRUCTIONAL MANUAL 

 

2750L-P/4500L-P/6000L-P 

August, 2001 

 

 

Rev. K 

-107- 

5.4 AUXILIARY 

POWER 

SUPPLY 

 
The Auxiliary Power Supply receives the +300 supply voltage from the Input Power Supply.  The +300 supply voltage is 
then changed to the +50 VDC supply voltage for operating the fans and relays.  In addition to the +50 VDC supply, 
+15VSW1 is also generated.  This supply voltage is used for the gate drive signal in the Amplifier Modules. 
 

5.5 

CURRENT LIMIT BOARD 

 
The Current Limit Board receives the oscillator signals identified as OSC A, B and C from the Oscillator Module.  
Analog switches on this board direct the oscillator signals to the respective amplifier module.  The analog switches 
switch the OSC A signal to the three amplifier inputs during 1-phase operation.  For 3-phase operation, OSC A, B and 
C are switched to the amplifiers A, B and C inputs respectively.  Gain adjustments are located on this board to match 
the gains of the 3 Amplifier Modules. 
 
The current limit circuits are also located on the Current Limit Board.  These circuits receive a DC signal from the Oscil-
lator Module, CLA, B and C, that is proportional to the current limit value.  This DC signal is compared to the output 
current.  The output current signal is identified as TA, TB and TC.   This signal is routed to the Current Limit Board from 
current transformers on the Range Relay Board.  If the output current exceeds the programmed value, an attenuator 
will limit the output voltage to a value that will cause the AC Power System to operate at a constant current.  If the 
output current limits the output voltage to 10% of the programmed voltage amplitude value, the output will default and 
an AMP FAULT error message will be displayed.  The error message will also be reported through the IEEE-488 
(GPIB) interface. 
 
The Current Limit Board has analog switches and summing amplifiers that are used for current measurements.  The 
outputs from the summing amplifiers, CT A, B and C, are routed to the Oscillator Module for measurement.  In the 
1-phase mode the current from all three output current transformers are summed together for measurement.  This 
signal is identified as CT A. 
 

5.6 INDICATOR 

BOARD 

 
The Indicator Board has the reference designator, A12.  This board has LED indicators for the HI RANGE, OVERTEMP 
and OVERLOAD conditions. 
 
A front panel selector switch is mounted on the Indicator Board.  This switch is used to connect the front panel analog 
meter, M1, to either the phase A, B or C output. 
 

5.7 RANGE 

RELAY 

BOARD 

 
The Range Relay Board has all of the AC Power System relays.  These Relays are operated from +50 VDC.  The 
output relay is opened by a logic low on the CNF control line.  The range relay is switched to the high voltage range by 
a logic low on the 

RNG HI

 control line.  The output is in the 1-phase mode when the PARALLEL control line is driven to 

approxi10 VDC. 
 
There are three current transformers on the Range Relay board.  These transformers generate an AC voltage that is 
proportional to the output current.  The voltages are identified as TA, TB and TC.  A 10 amp load current is represented 
by a 1.00 VAC signal in the 3-phase mode. 
 

5.8 AMPLIFIER 

MODULES 

 
The AC Power System has three Amplifier Modules.  In the 3- phase mode, one amplifier is used for each of the three 
outputs.  In the 1-phase mode, the three outputs are paralleled at the secondaries of the output transformers. 
 
The Amplifier Modules operate in a switch mode to obtain high efficiency.  These switch mode amplifiers operate at 200 
KHz. 

Содержание 12000L-1P
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000L-1P

Eastwood 14041 Instructions preview
14041
Бренд: Eastwood Страницы: 5
Makita DFL083F Quick Start Manual preview
DFL083F
Бренд: Makita Страницы: 6
Makita BFT043F Technical Information preview
BFT043F
Бренд: Makita Страницы: 14
Makita BFS440 Technical Information preview
BFS440
Бренд: Makita Страницы: 7
Makita BFL300F Technical Information preview
BFL300F
Бренд: Makita Страницы: 13
Makita HR3210C Parts Breakdown preview
HR3210C
Бренд: Makita Страницы: 4
Makita HR2410 Parts Breakdown preview
HR2410
Бренд: Makita Страницы: 5
Makita BFH040 Technical Information preview
BFH040
Бренд: Makita Страницы: 17
Makita HM1500 Parts Breakdown preview
HM1500
Бренд: Makita Страницы: 3
Makita HM1242C Technical Information preview
HM1242C
Бренд: Makita Страницы: 12
Makita HM1242C Parts Breakdown preview
HM1242C
Бренд: Makita Страницы: 3
Makita 4340FCT Parts Breakdown preview
4340FCT
Бренд: Makita Страницы: 3
Makita 6842 Technical Information preview
6842
Бренд: Makita Страницы: 16
Makita HM1100C Parts Breakdown preview
HM1100C
Бренд: Makita Страницы: 3
Makita 6826N Parts Breakdown preview
6826N
Бренд: Makita Страницы: 2
Makita HM0810B Manual preview
HM0810B
Бренд: Makita Страницы: 16
Makita 4341CT Specifications preview
4341CT
Бренд: Makita Страницы: 2
Makita 4324 Parts Manual preview
4324
Бренд: Makita Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды