California Instruments 12000L-1P Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 151

background image

INSTRUCTIONAL MANUAL

2750L-P/4500L-P/6000L-P

August, 2001

Rev. K

-96-

4.4 NONPERIODIC

CALIBRATION

If adjustments are required for these nonperiodic calibrations, the top cover of the AC Power System will have to be
removed. A nonperiodic calibration will only be required if a related assembly is repaired or if the performance is out of
specification.

4.4.1 OUTPUT

FREQUENCY CALIBRATION

Connect the Frequency Counter to the phase A output. Program the output to 135.0 volts and 400.0 Hz. Engage the
low-pass filter on the Frequency Counter to obtain the output frequency.

If the Frequency Counter does not indicate 400.000 ±0.004 Hz, adjust C43 for the correct frequency. Refer to Figure
4-1.

4.4.2

GAIN BALANCE ADJUSTMENT

CAUTION

The Gain Balance Adjustment should not be made unless an amplifier assembly has
been repaired. Each amplifier has been adjusted at the factory for an exact full scale
output voltage (135, 67.5, 156 or 200 volts for standard, LV, HV or EHV voltage
ranges) with a 5.000 VRMS amplifier input voltage. The amplifier input voltage may
be checked at TP4, TP5 and TP6 on the Current Limit Board for Phase A, B and C
amplifiers respectively. TP1 is the reference test point.

The following adjustment is for all power system models except the 2750L-3P, 4500L-3P and 6000L-3P. The 2750L-
3P, 4500L-3P and 6000L-3P do not require a gain balance adjustment. Before performing the adjustment, the top
cover of each power source must be removed.

4.4.3 GAIN

BALANCE

FOR

PARALLEL AMPLIFIERS

If applicable, program the output to the 1-phase mode. The following table shows the test point that will be used to
measure the circulating current between the amplifiers under a no-load condition. Jumper W2 on the Current Limit
Board must be installed for 4500L-1, 6000L-1, 9000L-1, 12000L-1, 13500L-1, 18000L-1 and 18000L-3.

AMPLIFIER

CURRENT

LIMIT BOARD TEST POINT (TP1 is ground)

A

TP10

B

TP2

C

TP3

Program 100 VAC. Measure the current from the B and C amplifier by measuring the voltage at TP2 and TP3
respectively. Adjust the amplifier GAIN adjustment (R104) on the respective amplifier for the lowest voltage (current) at
the respective test point. Use test point TP2 for making the gain adjustment (R104) for amplifier B. Use TP3 for
amplifier C.

For all slave power sources adjust the amplifier GAIN adjustments for the A, B and C amplifier. Use TP10 for amplifier
A.

1.

Check all of the amplifiers for the system being tested.

For the output from each amplifier of a given phase, the AC DVM should display less that 0.25 VAC
while the DVM is on the 200 VAC range.

2.

If any measurement from the GAIN BALANCE check is out of specification, the gain of the amplifier

«
...
98
99
100
101
102
...
»

Содержание 12000L-1P
























































































































































Отзывы:

Нет отзывов

Похожие инструкции для 12000L-1P

Бренд: Rapid Страницы: 6

Бренд: Akyga Страницы: 4

Бренд: Vanderbilt Страницы: 3

Бренд: Earlex Страницы: 4

Бренд: Parkside Performance Страницы: 134

Бренд: ?HC Страницы: 2

Бренд: Ulvac Страницы: 87

Бренд: ZENS Страницы: 10

Бренд: ELC Страницы: 12

CYBERCORE PLATINUM Series

Бренд: XPG Страницы: 50

Бренд: First Choice Страницы: 2

Бренд: HIKOKI Страницы: 20

Бренд: Robust Страницы: 44

Бренд: Wacker Neuson Страницы: 54

Бренд: Worldwide Страницы: 2

Бренд: BGS technic Страницы: 4

Бренд: Et system Страницы: 83

Бренд: Far Tools Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды