Cadillac Escalade 2020 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

SEATS AND RESTRAINTS

45

A DIC welcome message may
indicate driver number 1 or 2.

2. Adjust all available memory

features to the desired driving
position.

3. Press and release SET; a beep

will sound.

4. Immediately press and hold the

1 or 2 memory button matching
the above DIC welcome message
until two beeps sound.

If too much time passes between
releasing SET and pressing 1, the
memory position will not be
saved and two beeps will not
sound. Repeat Steps 3 and 4.

1 or 2 corresponds to the driver
number. See

“

Identifying Driver

Number

”

previously in this

section.

5. Repeat Steps 1

–

4 for a second

driver using 1 or 2.

To save the position for

B

and Easy

Exit Recall features, repeat Steps 1

–

4

using

B

. This saves the position for

getting out of the vehicle.

Save preferred memory feature
positions to both 1 and 2 if you are
the only driver.

Manually Recalling Memory
Positions

Press and hold 1, 2, or

B

to recall

the previously saved memory
positions if you are driver 1 or 2
identified in the DIC welcome
message. RKE transmitters 3

–

8 will

not recall memory positions.

To stop Manual Memory recall
movement, release 1, 2, or

B

or press

any of the following controls:

.

Power seat

.

Memory SET

.

Power mirror, with the driver or
passenger side mirror selected

.

Power steering wheel, if equipped

Auto Memory Recall

The vehicle identifies the number of
the current driver

’

s RKE transmitter

(1

–

8). See

Remote Keyless Entry (RKE)

System Operation

. If the RKE

transmitter is 1 or 2, and Auto

Memory Recall is enabled in vehicle
personalization, the positions saved to
the same memory button number 1 or
2 are automatically recalled when the
vehicle is turned on, or turned from
off to ACC/ACCESSORY. RKE
transmitters 3

–

8 will not provide

automatic memory recalls.

To turn Auto Memory Recall on or off,
see

“

Vehicle Personalization Settings

”

previously in this section and

Personalization

.

The shift lever must be in P (Park) to
start Auto Memory Recall. Auto
Memory Recall will complete if the
vehicle is shifted out of P (Park) prior
to reaching the saved memory
position.

To stop Auto Memory Recall
movement, turn the vehicle off or
press any of the following controls:

.

Power seat

.

Memory SET, 1, 2, or

B

.

Power mirror, with the driver or
passenger side mirror selected

.

Power steering wheel, if equipped

«
...
43
44
45
46
47
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Pacbrake Страницы: 9

Бренд: Actia Страницы: 37

RUDDER ANGLE INDICATOR

Бренд: VDO Страницы: 8

Бренд: Chevrolet Страницы: 372

Бренд: C-KO Страницы: 4

Бренд: Caraudio-Systems Страницы: 9

Бренд: Cadillac Страницы: 20

Бренд: Pyle Страницы: 8

CMPC-22 Fujitsu-Siemens PocketLoox 410

Бренд: Carcomm Страницы: 2

nERGY ETSA200R-PA

Бренд: Soundoff Signal Страницы: 3

Бренд: Truma Страницы: 10

Бренд: Edelbrock Страницы: 1

Airgo Active cushion / Comfort

Бренд: TOGU Страницы: 2

Бренд: Lund Страницы: 12

Бренд: Bulldog Security Страницы: 7

Бренд: Yakima Страницы: 9

Бренд: QA1 Страницы: 4

Бренд: Safe Fleet Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды