Cadillac Escalade 2020 Скачать руководство пользователя страница 200 | Manualshive

Страница: 200 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

200

DRIVING AND OPERATING

Before leaving the vehicle, check for
the

Y

light to ensure that the

parking brake is applied.

EPB Apply

To apply the EPB:

1. Be sure the vehicle is at a

complete stop.

2. Lift up the EPB switch

momentarily.

The

Y

light will flash and then stay

on once the EPB is fully applied. If
the

Y

light flashes continuously,

then the EPB is only partially applied
or there is a problem with the EPB.
A DIC message will display. Release
the EPB and try to apply it again.
If the light does not come on, or keeps
flashing, have the vehicle serviced. Do
not drive the vehicle if the

Y

light is

flashing. See your dealer. See

Parking Brake Light

.

If the

8

light is on, press the EPB

switch and hold it. Continue to hold
the switch until the

Y

light remains

on. If the

8

light remains on, see your

dealer.

If the EPB is applied while the vehicle
is moving, the vehicle will decelerate
as long as the switch is pulled. If the
switch is pulled until the vehicle
comes to a stop, the EPB will remain
applied.

The vehicle may automatically apply
the EPB in some situations when the
vehicle is not moving. This is normal,
and is done to periodically check the
correct operation of the EPB system.

If the EPB fails to apply, block the rear
wheels to prevent vehicle movement.

EPB Release

To release the EPB:

1. Turn the ignition on or to ACC/

ACCESSORY.

2. Apply and hold the brake pedal.

3. Press the EPB switch

momentarily.

The EPB is released when the

Y

light is off.

If the

8

light is on, release the EPB by

pressing and holding the EPB switch.
Continue to hold the switch until
the

Y

light is off. If either light stays

on after release is attempted, see your
dealer.

Caution

Driving with the parking brake on
can overheat the brake system and
cause premature wear or damage to
brake system parts. Make sure that
the parking brake is fully released
and the brake warning light is off
before driving.

Automatic EPB Release

The EPB will automatically release if
the vehicle is running, placed into
gear, and an attempt is made to drive
away. Avoid rapid acceleration when
the EPB is applied, to preserve parking
brake lining life.

«
...
198
199
200
201
202
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: RaceChip Страницы: 12

NPL-TV 7874 DIGITAL

Бренд: Napoli Страницы: 20

Бренд: TBC Страницы: 12

Бренд: Brodit Страницы: 2

Бренд: Whispbar Страницы: 77

Бренд: Yakima Страницы: 13

Бренд: Menabo Страницы: 11

PACCAR PACMOBILE 20

Бренд: DAF Страницы: 18

Бренд: Actia Страницы: 102

Бренд: Renault Страницы: 340

XEBRA ZAPCAR Series

Бренд: Zap Страницы: 16

Бренд: travall Страницы: 2

Бренд: Gacell Страницы: 12

Бренд: Gator Страницы: 6

Бренд: BrandMotion Страницы: 6

Бренд: Jaeger Страницы: 16

Бренд: Brodit Страницы: 2

Бренд: Toyota Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды