Cadillac Escalade 2020 Скачать руководство пользователя страница 295 | Manualshive

Страница: 295 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

295

There are two minutes to match the
first tire/wheel position, and
five minutes overall to match all four
tire/wheel positions. If it takes longer,
the matching process stops and must
be restarted.

The TPMS sensor matching process is:

1. Set the parking brake.

2. Place the vehicle in Service

Mode. See

Ignition Positions

.

3. Make sure the Tire Pressure info

display option is turned on. The
info displays on the DIC can be
turned on and off through the
Settings menu. See

Information Center (DIC)

4. Use the five-way DIC control on

the right side of the steering
wheel to scroll to the Tire
Pressure screen under the DIC
info page. See

Driver Information

.

5. Press and hold SEL in the center

of the five-way DIC control.

The horn sounds twice to signal
the receiver is in relearn mode
and the TIRE LEARNING ACTIVE
message displays on the DIC
screen.

6. Start with the driver side

front tire.

7. Place the relearn tool against the

tire sidewall, near the valve stem.
Then press the button to activate
the TPMS sensor. A horn chirp
confirms that the sensor
identification code has been
matched to this tire and wheel
position.

8. Proceed to the passenger side

front tire, and repeat the
procedure in Step 7.

9. Proceed to the passenger side

rear tire, and repeat the
procedure in Step 7.

10. Proceed to the driver side rear

tire, and repeat the procedure in
Step 7. The horn sounds two
times to indicate the sensor
identification code has been
matched to the driver side rear
tire, and the TPMS sensor

matching process is no longer
active. The TIRE LEARNING
ACTIVE message on the DIC
display screen goes off.

11. Turn the vehicle off.

12. Set all four tires to the

recommended air pressure level
as indicated on the Tire and
Loading Information label.

Tire Inspection

We recommend that the tires,
including the spare tire, if the
vehicle has one, be inspected for
signs of wear or damage at least
once a month.

Replace the tire if:

.

The indicators at three or more
places around the tire can
be seen.

.

There is cord or fabric showing
through the tire's rubber.

.

The tread or sidewall is
cracked, cut, or snagged deep
enough to show cord or fabric.

«
...
293
294
295
296
297
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Ranger design Страницы: 6

Бренд: Oldsmobile Страницы: 360

1973 Crown Hardtop

Бренд: Toyota Страницы: 50

Бренд: kincrome Страницы: 6

Stratus LHD 1997

Бренд: Chrysler Страницы: 1534

Carpower CAP-20

Бренд: Monacor Страницы: 2

Hypercharger HYC 075

Бренд: Alpitronic Страницы: 64

Бренд: Kia Страницы: 51

V70XC Cross country 1998

Бренд: Volvo Страницы: 262

Бренд: ECS Страницы: 4

Бренд: Whispbar Страницы: 15

Omni-Bike Sport Ducato

Бренд: OMNISTOR Страницы: 5

2008 Savana Van

Бренд: GMC Страницы: 402

PRO-FLO XT 3527

Бренд: Edelbrock Страницы: 39

Бренд: Toyota Страницы: 26

Бренд: Quadratec Страницы: 8

Бренд: Valueline Страницы: 40

QuadraTop Adventure Top 1113.00 Series

Бренд: Quadratec Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды