Cadillac Escalade 2020 Скачать руководство пользователя страница 325 | Manualshive

Страница: 325 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

325

2. Remove excess moisture by

gently wringing until water does
not drip from the cleaning cloth.

3. Start on the outside edge of the

soil and gently rub toward the
center. Fold the cleaning cloth to
a clean area frequently to
prevent forcing the soil in to the
fabric.

4. Continue gently rubbing the

soiled area until there is no
longer any color transfer from
the soil to the cleaning cloth.

5. If the soil is not completely

removed, use a mild soap
solution followed only by plain
water.

If the soil is not completely removed,
it may be necessary to use a
commercial upholstery cleaner or spot
lifter. Test a small hidden area for
colorfastness before using a
commercial upholstery cleaner or spot
lifter. If ring formation occurs, clean
the entire fabric or carpet.

After cleaning, use a paper towel to
blot excess moisture.

Cleaning High Gloss Surfaces
and Vehicle Information and
Radio Displays

Use a microfiber cloth on high gloss
surfaces or vehicle displays. First, use
a soft bristle brush to remove dirt that
can scratch the surface. Then gently
clean by rubbing with a microfiber
cloth. Never use window cleaners or
solvents. Periodically hand wash the
microfiber cloth separately, using mild
soap. Do not use bleach or fabric
softener. Rinse thoroughly and air dry
before next use.

Caution

Do not attach a device with a
suction cup to the display. This may
cause damage and would not be
covered by the vehicle warranty.

Instrument Panel, Leather, Vinyl,
Other Plastic Surfaces, Low
Gloss Paint Surfaces, and
Natural Open Pore Wood
Surfaces

Use a soft microfiber cloth dampened
with water to remove dust and loose
dirt. For a more thorough cleaning,
use a soft microfiber cloth dampened
with a mild soap solution.

Caution

Soaking or saturating leather,
especially perforated leather, as well
as other interior surfaces, may
cause permanent damage. Wipe
excess moisture from these surfaces
after cleaning and allow them to
dry naturally. Never use heat,
steam, or spot removers. Do not use
cleaners that contain silicone or
wax-based products. Cleaners
containing these solvents can
permanently change the appearance
and feel of leather or soft trim, and
are not recommended.

«
...
323
324
325
326
327
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Saab Страницы: 75

Бренд: Jeep Страницы: 322

Бренд: Jeep Страницы: 341

Бренд: Jeep Страницы: 310

Бренд: Jeep Страницы: 189

Бренд: Jeep Страницы: 26

Бренд: Jeep Страницы: 21

Бренд: Yakima Страницы: 11

Бренд: Kia Страницы: 385

Бренд: Dacia Страницы: 238

Бренд: Atera Страницы: 10

4500 CHASSIS CAB 2012

Бренд: RAM Страницы: 7

Бренд: BMW Страницы: 189

Бренд: Pontiac Страницы: 486

Бренд: RAM Страницы: 148

Бренд: Hamron Страницы: 36

Бренд: Whispbar Страницы: 14

Бренд: Acura Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды