Cadillac Escalade 2020 Скачать руководство пользователя страница 320 | Manualshive

Страница: 320 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

320

VEHICLE CARE

If using an automatic car wash, follow
the car wash instructions. The
windshield wiper and rear window
wiper, if equipped, must be off.
Remove any accessories that may be
damaged or interfere with the car
wash equipment.

Rinse the vehicle well, before washing
and after, to remove all cleaning
agents completely. If they are allowed
to dry on the surface, they could stain.

Dry the finish with a soft, clean
chamois or an all-cotton towel to
avoid surface scratches and water
spotting.

Finish Care

Application of aftermarket clearcoat
sealant/wax materials is not
recommended. If painted surfaces are
damaged, see your dealer to have the
damage assessed and repaired. Foreign
materials such as calcium chloride
and other salts, ice melting agents,
road oil and tar, tree sap, bird
droppings, chemicals from industrial
chimneys, etc., can damage the
vehicle's finish if they remain on
painted surfaces. Wash the vehicle as

soon as possible. If necessary, use
non-abrasive cleaners that are marked
safe for painted surfaces to remove
foreign matter.

Occasional hand waxing or mild
polishing should be done to remove
residue from the paint finish. See your
dealer for approved cleaning products.

Do not apply waxes or polishes to
uncoated plastic, vinyl, rubber, decals,
simulated wood, or flat paint as
damage can occur.

Caution

Machine compounding or
aggressive polishing on a basecoat/
clearcoat paint finish may damage
it. Use only non-abrasive waxes and
polishes that are made for a
basecoat/clearcoat paint finish on
the vehicle.

To keep the paint finish looking new,
keep the vehicle garaged or covered
whenever possible.

Protecting Exterior Bright Metal
Moldings

Caution

Failure to clean and protect the
bright metal moldings can result in
a hazy white finish or pitting. This
damage would not be covered by
the vehicle warranty.

The bright metal moldings on the
vehicle are aluminum, chrome or
stainless steel. To prevent damage
always follow these cleaning
instructions:

.

Be sure the molding is cool to the
touch before applying any cleaning
solution.

.

Use only approved cleaning
solutions for aluminum, chrome or
stainless steel. Some cleaners are
highly acidic or contain alkaline
substances and can damage the
moldings.

.

Always dilute a concentrated
cleaner according to the
manufacturer

’

s instructions.

«
...
318
319
320
321
322
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: cam Страницы: 28

Бренд: Mazda Страницы: 527

2008 Escalade EXT

Бренд: Cadillac Страницы: 496

Бренд: Chevrolet Страницы: 2

Бренд: Kia Страницы: 54

Бренд: Road Ranger Страницы: 22

Бренд: Quadratec Страницы: 12

Бренд: Caltrend Страницы: 3

Бренд: Weltmann KFZ-Teile Страницы: 12

Бренд: Caraudio-Systems Страницы: 9

Бренд: Ford Страницы: 2

Бренд: Green Valley Страницы: 17

2004 JR41 Stratus Sedan

Бренд: Dodge Страницы: 273

Бренд: Buick Страницы: 20

Бренд: Buick Страницы: 394

Бренд: Mazda Страницы: 196

Бренд: Skoda Страницы: 288

Camry Hybrid 2012

Бренд: Toyota Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды