Cadillac Escalade 2020 Скачать руководство пользователя страница 207 | Manualshive

Страница: 207 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

207

When the cruise control has been set
to the desired speed, a green cruise
control indicator appears on the
instrument cluster and a cruise set
speed message appears on the Driver
Information Center (DIC) and
Head-Up Display (HUD), if equipped.

Resuming a Set Speed

If the cruise control is set at a desired
speed and then the brakes are applied
or

*

is pressed, the cruise control is

disengaged without erasing the set
speed from memory.

Once the vehicle speed reaches about
40 km/h (25 mph) or more, press +RES
up briefly. The vehicle returns to the
previous set speed.

Increasing Speed While Cruise
Control is at a Set Speed

If the cruise control system is already
activated:

.

Press and hold +RES up until the
vehicle accelerates to the desired
speed, then release it.

.

To increase vehicle speed in small
increments, press +RES up briefly.
For each press, the vehicle goes
about 1 km/h (1 mph) faster.

The speedometer reading can be
displayed in either English or metric
units. See

Instrument Cluster

.

The increment value used depends on
the units displayed.

Reducing Speed While Cruise
Control is at a Set Speed

If the cruise control system is already
activated:

.

Press and hold SET

−

down until

the desired lower speed is reached,
then release it.

.

To decrease the vehicle speed in
small increments, press SET

−

down briefly. For each press, the
vehicle goes about 1 km/h (1 mph)
slower.

The speedometer reading can be
displayed in either English or metric
units. See

Instrument Cluster

.

The increment value used depends on
the units displayed.

Passing Another Vehicle While
Using Cruise Control

Use the accelerator pedal to increase
the vehicle speed. When you take your
foot off the pedal, the vehicle will slow
down to the previous set cruise speed.

While pressing the accelerator pedal
or shortly following the release to
override cruise, briefly applying the
SET

−

control will result in cruise set

to the current vehicle speed.

Using Cruise Control on Hills

How well the cruise control works on
hills depends on the vehicle speed, the
load, and the steepness of the hills.
When going up steep hills, pressing
the accelerator pedal may be
necessary to maintain vehicle speed.
When going downhill, Cruise Grade
Braking helps maintain the driver
selected speed.

Cruise Grade Braking is enabled when
the vehicle is started and cruise
control is active. It is not enabled in
Range Selection Mode. It assists in
maintaining driver selected speed

«
...
205
206
207
208
209
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: A-Tach Mounts Страницы: 2

Бренд: SCC Страницы: 4

Бренд: Meta System Страницы: 22

Бренд: Gator Страницы: 8

Бренд: benbat Страницы: 14

Бренд: SPL Страницы: 5

Бренд: Gator Страницы: 6

Бренд: Elinchrom Страницы: 101

Бренд: Prorack Страницы: 15

Interlock 700 Series

Бренд: Scania Страницы: 82

PRIME DESIGN VCR-TC11B

Бренд: Safe Fleet Страницы: 12

Бренд: Club Car Страницы: 286

Бренд: Voxx Electronics Страницы: 15

Бренд: Prorack Страницы: 14

Бренд: Edelbrock Страницы: 2

Бренд: Mercedes-Benz Страницы: 93

Ridesmart KMA-610

Бренд: KlipXtreme Страницы: 12

Бренд: TATA Motors Страницы: 232

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды