Cadillac Escalade 2020 Скачать руководство пользователя страница 321 | Manualshive

Страница: 321 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

321

.

Do not use cleaners that are not
intended for automotive use.

.

Use a nonabrasive wax on the
vehicle after washing to protect
and extend the molding finish.

Cleaning Exterior Lamps/Lenses,
Emblems, Decals, and Stripes

Use only lukewarm or cold water, a
soft cloth, and a car washing soap to
clean exterior lamps, lenses, emblems,
decals, and stripes. Follow instructions
under "Washing the Vehicle"
previously in this section.

Lamp covers are made of plastic, and
some have a UV protective coating. Do
not clean or wipe them when dry.

Do not use any of the following on
lamp covers:

.

Abrasive or caustic agents.

.

Washer fluids and other cleaning
agents in higher concentrations
than suggested by the
manufacturer.

.

Solvents, alcohols, fuels, or other
harsh cleaners.

.

Ice scrapers or other hard items.

.

Aftermarket appearance caps or
covers while the lamps are
illuminated, due to excessive heat
generated.

Caution

Failure to clean lamps properly can
cause damage to the lamp cover
that would not be covered by the
vehicle warranty.

Caution

Using wax on low gloss black finish
stripes can increase the gloss level
and create a non-uniform finish.
Clean low gloss stripes with soap
and water only.

Air Intakes

Clear debris from the air intakes,
between the hood and windshield,
when washing the vehicle.

Windshield and Wiper Blades

Clean the outside of the windshield
with glass cleaner.

Clean rubber blades using a lint-free
cloth or paper towel soaked with
windshield washer fluid or a mild
detergent. Wash the windshield
thoroughly when cleaning the blades.
Bugs, road grime, sap, and a buildup
of vehicle wash/wax treatments may
cause wiper streaking.

Replace the wiper blades if they are
worn or damaged. Damage can be
caused by extreme dusty conditions,
sand, salt, heat, sun, snow, and ice.

Weatherstrips

Apply weatherstrip lubricant on
weatherstrips to make them last
longer, seal better, and not stick or
squeak. Lubricate weatherstrips at
least once a year. Hot, dry climates
may require more frequent
application. Black marks from rubber
material on painted surfaces can be
removed by rubbing with a clean
cloth. See

Recommended Fluids and

«
...
319
320
321
322
323
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Acdeos Страницы: 38

Бренд: B-Speech Страницы: 18

AUDI 4G HIGHEND

Бренд: KAP Страницы: 20

Dodge Charger TufBox

Бренд: TUFLOC Страницы: 6

Бренд: Audi Страницы: 12

Бренд: EZTRUNK Страницы: 3

Бренд: Gator Страницы: 2

Бренд: Metra Electronics Страницы: 8

Бренд: Cadillac Страницы: 20

Бренд: iDataLink Страницы: 6

FXX ATM Emulator

Бренд: BMW Страницы: 5

Бренд: Mobridge Страницы: 20

Jumpy Miltispace

Бренд: CITROËN Страницы: 164

Бренд: Directed Страницы: 30

Бренд: Maserati Страницы: 37

Бренд: Butts of Bawtry Страницы: 2

LineCast Auto FM

Бренд: Belkin Страницы: 15

Бренд: Rover Страницы: 285

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды