Cadillac Escalade 2020 Скачать руководство пользователя страница 183 | Manualshive

Страница: 183 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

183

Stopping the Engine/LOCK/OFF (No
Indicator Lights) :

When the vehicle

is stopped, press ENGINE START/
STOP once to turn the engine off.

If the vehicle is in P (Park), the
ignition will turn off, and Retained
Accessory Power (RAP) will remain
active. See

Retained Accessory Power

If the vehicle is not in P (Park), the
ignition will return to ACC/
ACCESSORY and display the message
SHIFT TO PARK in the Driver
Information Center (DIC). When the
vehicle is shifted into P (Park), the
ignition will turn off.

Do not turn the engine off when the
vehicle is moving. This will cause a
loss of power assist in the brake and
steering systems and disable the
airbags.

The vehicle may have an electric
steering column lock. The lock is
activated when the ignition is turned
off and either front door is opened.
A sound may be heard as the lock
actuates or releases. The steering
column lock may not release with the

wheels turned off center. If this
happens, the vehicle may not start.
Move the steering wheel from left to
right while attempting to start the
vehicle. If this does not work, the
vehicle needs service.

If the vehicle must be shut off in an
emergency:

1. Brake using a firm and steady

pressure. Do not pump the
brakes repeatedly. This may
deplete power assist, requiring
increased brake pedal force.

2. Shift the vehicle to N (Neutral).

This can be done while the
vehicle is moving. After shifting
to N (Neutral), firmly apply the
brakes and steer the vehicle to a
safe location.

3. Come to a complete stop, shift to

P (Park), and turn the ignition
off. On vehicles with an
automatic transmission, the shift
lever must be in P (Park) to turn
the ignition off.

4. Set the parking brake. See

Parking Brake

or

Electric Parking Brake

{

Warning

Turning off the vehicle while
moving may cause loss of power
assist in the brake and steering
systems and disable the airbags.
While driving, only shut the vehicle
off in an emergency.

If the vehicle cannot be pulled over,
and must be shut off while driving,
press and hold ENGINE START/STOP
for longer than two seconds, or press
twice in five seconds.

ACC/ACCESSORY (Amber Indicator
Light) :

This mode allows some

electrical accessories to be used when
the engine is off.

With the ignition off, pressing the
button one time without the brake
pedal applied will place the ignition
system in ACC/ACCESSORY.

The ignition will switch from ACC/
ACCESSORY to off after five minutes
to prevent battery rundown.

«
...
181
182
183
184
185
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: ZAPTEC Страницы: 240

Бренд: Ranger design Страницы: 6

Бренд: Eclipse Страницы: 6

Бренд: Uniden Страницы: 16

Бренд: Uniden Страницы: 20

Бренд: Mazda Страницы: 527

2008 Escalade EXT

Бренд: Cadillac Страницы: 496

Бренд: Whispbar Страницы: 77

Бренд: Honda Страницы: 208

2012 Truck Chassis cab

Бренд: RAM Страницы: 506

Бренд: Toro Страницы: 24

Бренд: SuperATV Страницы: 7

Бренд: Veldo Teknoloji Страницы: 32

Бренд: FALCON RIDGE Страницы: 4

Бренд: Ferve Страницы: 28

Бренд: Saab Страницы: 37

Бренд: Hama Страницы: 13

Бренд: Subaru Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды