Cadillac Escalade 2020 Скачать руководство пользователя страница 74 | Manualshive

Страница: 74 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

74

SEATS AND RESTRAINTS

1. Turn the vehicle off.

2. Remove any additional material

from the seat, such as blankets,
cushions, seat covers, seat
heaters, or seat massagers.

3. Place the seatback in the fully

upright position.

4. Have the person sit upright in

the seat, centered on the seat
cushion, with legs comfortably
extended.

5. If the shoulder portion of the

belt is pulled out all the way, the
child restraint locking feature
will be engaged. This may
unintentionally cause the
passenger sensing system to turn
the airbag off for some
adult-sized occupants. If this
happens, unbuckle the belt, let
the belt go back all the way, and
then buckle the belt again
without pulling the belt out all
the way.

6. Restart the vehicle and have the

person remain in this position
for two to three minutes after the
on indicator is lit.

{

Warning

If the front outboard passenger
airbag is turned off for an
adult-sized occupant, the airbag will
not be able to inflate and help
protect that person in a crash,
resulting in an increased risk of
serious injury or even death. An
adult-sized occupant should not
ride in the front outboard passenger
seat, if the passenger airbag off
indicator is lit.

Additional Factors Affecting
System Operation

Seat belts help keep the passenger in
position on the seat during vehicle
maneuvers and braking, which helps
the passenger sensing system
maintain the passenger airbag status.
See

“

Seat Belts

”

and

“

Child Restraints

”

in the Index for additional
information about the importance of
proper restraint use.

A thick layer of additional material,
such as a blanket or cushion,
or aftermarket equipment such as seat
covers, seat heaters, and seat
massagers can affect how well the
passenger sensing system operates.
We recommend that you not use seat
covers or other aftermarket equipment
except when approved by GM for your
specific vehicle. See

Adding Equipment

to the Airbag-Equipped Vehicle

for

more information about modifications
that can affect how the system
operates.

The on indicator may be lit if an
object, such as a briefcase, handbag,
grocery bag, laptop, or other electronic
device, is put on an unoccupied seat.
If this is not desired, remove the
object from the seat.

{

Warning

Stowing articles under the
passenger seat or between the
passenger seat cushion and
seatback may interfere with the
proper operation of the passenger
sensing system.

«
...
72
73
74
75
76
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Jeep Страницы: 42

Бренд: Jeep Страницы: 44

Бренд: Cadillac Страницы: 20

Бренд: Jeep Страницы: 7

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 354

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 10

2013 Escalade ESV

Бренд: Cadillac Страницы: 524

Бренд: Cadillac Страницы: 20

Бренд: Cadillac Страницы: 438

Бренд: Cadillac Страницы: 450

2011 Escalade Hybrid

Бренд: Cadillac Страницы: 94

2011 Escalade Hybrid

Бренд: Cadillac Страницы: 94

Бренд: Cadillac Страницы: 78

Бренд: Cadillac Страницы: 8

Бренд: Cadillac Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды