Cadillac Escalade 2020 Скачать руководство пользователя страница 294 | Manualshive

Страница: 294 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

294

VEHICLE CARE

4. Add air to the tire that is

underinflated. The turn signal
lamp will flash.

When the recommended
pressure is reached, the horn
sounds once and the turn signal
lamp will stop flashing and
briefly turn solid.

Repeat these steps for all
underinflated tires that have
illuminated the low tire pressure
warning light.

{

Warning

Overinflating a tire could cause the
tire to rupture and you or others
could be injured. Do not exceed the
maximum pressure listed on the
tire sidewall.

If the tire is overinflated by more than
35 kPa (5 psi), the horn will sound
multiple times and the turn signal
lamp will continue to flash for several
seconds after filling stops. To release
and correct the pressure, while the
turn signal lamp is still flashing,

briefly press the center of the valve
stem. When the recommended
pressure is reached, the horn
sounds once.

If the turn signal lamp does not flash
within 15 seconds after starting to
inflate the tire, the tire fill alert has
not been activated or is not working.

If the hazard warning flashers are on,
the tire fill alert visual feedback will
not work properly.

The TPMS will not activate the tire fill
alert properly under the following
conditions:

.

There is interference from an
external device or transmitter.

.

The air pressure from the inflation
device is not sufficient to inflate
the tire.

.

There is a malfunction in
the TPMS.

.

There is a malfunction in the horn
or turn signal lamps.

.

The identification code of the
TPMS sensor is not registered to
the system.

.

The battery of the TPMS sensor
is low.

If the tire fill alert does not operate
due to TPMS interference, move the
vehicle about 1 m (3 ft) back or
forward and try again. If the tire fill
alert feature is not working, use a tire
pressure gauge.

TPMS Sensor Matching Process

Each TPMS sensor has a unique
identification code. The identification
code needs to be matched to a new
tire/wheel position after rotating the
vehicle

’

s tires or replacing one or more

of the TPMS sensors. The TPMS
sensor matching process should also
be performed after replacing a spare
tire with a road tire containing the
TPMS sensor. The malfunction light
and the DIC message should go off at
the next ignition cycle. The sensors
are matched to the tire/wheel
positions, using a TPMS relearn tool,
in the following order: driver side
front tire, passenger side front tire,
passenger side rear tire, and driver
side rear tire. See your dealer for
service or to purchase a relearn tool.

«
...
292
293
294
295
296
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Saab Страницы: 75

Бренд: Daihatsu Страницы: 1718

Бренд: Edelbrock Страницы: 2

Бренд: FALCON RIDGE Страницы: 8

Бренд: Scosche Страницы: 8

Бренд: Parkeon Страницы: 43

2011 A3 Sportback

Бренд: Audi Страницы: 29

Бренд: Magneti Marelli Страницы: 2

Akerstroms Tx700

Бренд: LXE Страницы: 146

Бренд: Draw tite Страницы: 4

Бренд: Horn Tools Страницы: 12

Бренд: Volvo Страницы: 10

Telescoping Computer Base C-TCB-34

Бренд: Havis-Shields Страницы: 1

Бренд: PEUGEOT Страницы: 107

CF-UFORCE-DRW01

Бренд: FALCON RIDGE Страницы: 6

Бренд: Volvo Страницы: 16

1995 Roadmaster

Бренд: Buick Страницы: 340

Бренд: Edelbrock Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды