Cadillac Escalade 2020 Скачать руководство пользователя страница 147 | Manualshive

Страница: 147 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

LIGHTING

147

Lighting

Exterior Lighting

Exterior Lamp Controls . . . . . . . . . . 147
Exterior Lamps Off Reminder . . . 148
Headlamp High/Low-Beam

Changer . . . . . . . . . . . . . . . . . . . . . . . . . . 149

Flash-to-Pass . . . . . . . . . . . . . . . . . . . . . 149
Daytime Running

Lamps (DRL) . . . . . . . . . . . . . . . . . . . . 149

Automatic Headlamp System . . . 149
Hazard Warning Flashers . . . . . . . . 151
Turn and Lane-Change

Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

Cornering Lamps . . . . . . . . . . . . . . . . . 151

Interior Lighting

Instrument Panel Illumination

Control . . . . . . . . . . . . . . . . . . . . . . . . . . 152

Dome Lamps . . . . . . . . . . . . . . . . . . . . . 152
Reading Lamps . . . . . . . . . . . . . . . . . . . 153

Lighting Features

Entry Lighting . . . . . . . . . . . . . . . . . . . . 153
Exit Lighting . . . . . . . . . . . . . . . . . . . . . . 153
Battery Load Management . . . . . . 154
Battery Power Protection . . . . . . . . 154
Exterior Lighting Battery

Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154

Exterior Lighting

Exterior Lamp Controls

The exterior lamp control is on the
instrument panel to the left of the
steering wheel.

Turn the control to the following
positions:

P

:

Turns off the automatic

headlamps and Daytime Running
Lamps (DRL). Turning the headlamp
control to

P

again will turn the

automatic headlamps or DRL back on.

AUTO :

Automatically turns the

exterior lamps on and off, depending
on outside lighting.

;

:

Turns on the parking lamps

including all lamps, except the
headlamps.

2

:

Turns on the headlamps together

with the parking lamps and
instrument panel lights.

When the headlamps are turned on
while the vehicle is on, the headlamps
will turn off automatically 10 minutes
after the ignition is turned off. When
the headlamps are turned on while
the vehicle is off, the headlamps will
stay on for 10 minutes before
automatically turning off to prevent
the battery from being drained. Turn
the headlamp control to off and then
back to the headlamp on position to
make the headlamps stay on for an
additional 10 minutes.

IntelliBeam

®

System

If equipped, this system turns the
vehicle's high-beam headlamps on and
off according to surrounding traffic
conditions.

The system turns the high-beam
headlamps on when it is dark enough
and there is no other traffic present.

«
...
145
146
147
148
149
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Kargo Master Страницы: 5

Бренд: Samsung Страницы: 133

Бренд: Back View Страницы: 168

Бренд: Saab Страницы: 10

Бренд: Pacbrake Страницы: 14

Бренд: Masterack Страницы: 4

Бренд: Over Armour Offroad Страницы: 5

Бренд: PullRite Страницы: 10

Бренд: Cadillac Страницы: 522

Бренд: Ratio Страницы: 12

Бренд: Horn Tools Страницы: 8

Бренд: Gator Страницы: 6

Бренд: F.lli Menabo Страницы: 16

Бренд: Webasto Страницы: 44

Бренд: Setma Страницы: 13

Бренд: Hama Страницы: 39

Electronic Parking Disc 3

Бренд: Jacob Jensen Страницы: 17

Бренд: Yakima Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды