Cadillac Escalade 2020 Скачать руководство пользователя страница 211 | Manualshive

Страница: 211 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

211

present and moved. See

“

Approaching

and Following a Vehicle

”

later in this

section.

Once ACC has resumed, if there is no
vehicle ahead, if the vehicle ahead is
beyond the selected following gap,
or if the vehicle has exited a sharp
curve, then the vehicle speed will
increase to the set speed.

Increasing Speed While ACC is at a
Set Speed

Do one of the following:

.

Use the accelerator to get to the
higher speed. Press SET

–

down.

Release the control and the
accelerator pedal. The vehicle will
now cruise at the higher speed.

When the accelerator pedal is
pressed, ACC will not brake
because it is overridden. The ACC
indicator will turn blue on the
instrument cluster.

.

Press and hold +RES up until the
desired set speed appears on the
display, then release it.

.

To increase speed in small
increments, briefly press +RES up.
For each press, the vehicle speed
increases by 1 km/h (1 mph).

.

To increase speed in larger
increments, press and briefly hold
+RES up. For each press, the
vehicle speed increases by
5 km/h (5 mph).

When it is determined there is no
vehicle ahead or the vehicle ahead is
beyond the selected following gap, the
vehicle speed will increase to the set
speed.

The set speed can also be increased
while the vehicle is stopped.

.

If stopped with the brake applied,
press RES+ until the desired set
speed is displayed.

.

If ACC is holding the vehicle at a
stop and there is another vehicle
directly ahead, pressing RES+ will
increase the set speed. Pressing
RES+ when there is no longer a
vehicle ahead will cause ACC to
resume.

Reducing Speed While ACC is at a
Set Speed

Do one of the following:

.

Use the brake to get to the desired
lower speed. Release the brake and
press SET

–

. The vehicle will now

cruise at the lower speed.

.

Press and hold SET

–

down until

the desired lower speed is reached,
then release it.

.

To decrease speed in smaller
increments, briefly press SET

−

down. For each press, the vehicle
speed increases by 1 km/h (1 mph).

.

To decrease speed in larger
increments, press and briefly hold
SET

−

down. For each press, the

vehicle speed decreases by
5 km/h (5 mph).

.

To decrease speed while the
vehicle is stopped, press SET

−

until the desired set speed is
displayed.

«
...
209
210
211
212
213
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

Бренд: Mazda Страницы: 4

Бренд: Camcar Страницы: 2

Бренд: TATA Motors Страницы: 161

Бренд: TAUBENREUTHER Страницы: 11

Бренд: Yakima Страницы: 15

Бренд: Suzuki Страницы: 353

Бренд: Torklift Страницы: 16

ANDROID INTERFACE

Бренд: GMC Страницы: 18

Бренд: Prorack Страницы: 15

BLADE-AL(TB)-TL2

Бренд: iDataLink Страницы: 9

Бренд: Magneti Marelli Страницы: 2

Бренд: EUFAB Страницы: 52

Бренд: EZTRUNK Страницы: 3

Бренд: P-Invent Страницы: 4

Бренд: Hyundai Страницы: 11

Бренд: T-Mobile Страницы: 2

Бренд: Abrams Страницы: 12

Бренд: Lantronix Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды