Cadillac Escalade 2020 Скачать руководство пользователя страница 144 | Manualshive

Страница: 144 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

144

INSTRUMENTS AND CONTROLS

instructions refer to a garage door
opener, but can be used for other
devices.

Do not use the Universal Remote
system with any garage door opener
that does not have the stop and
reverse feature. This includes any
garage door opener model
manufactured before April 1, 1982.

Read the instructions completely
before programming the Universal
Remote system. It may help to have
another person assist with
programming process.

Keep the original hand-held
transmitter for use in other vehicles
as well as for future programming.
Erase the programming when vehicle
ownership is terminated. See

“

Erasing

Universal Remote System Buttons

”

later in this section.

To program a garage door opener,
park outside directly in line with and
facing the garage door opener receiver.
Clear all people and objects near the
garage door.

Make sure the hand-held transmitter
has a new battery for quick and
accurate transmission of the
radio-frequency signal.

Programming the Universal
Remote System

The Universal Remote system is
compatible with radio-frequency
devices operating between
433-434 MHz.

For questions or programming help,
see www.homelink.com/gm.

Programming involves time-sensitive
actions, and may time out causing the
procedure to be repeated.

To program up to three devices:

1. Hold the end of the hand-held

transmitter about 3 to 8 cm (1 to
3 in) away from the Universal
Remote system buttons with the
indicator light in view. The
hand-held transmitter was
supplied by the manufacturer of
the garage door opener receiver.

2. At the same time, press and hold

both the hand-held transmitter
button and one of the three

Universal Remote system
buttons to be used to operate the
garage door. Do not release either
button until the indicator light
goes from a slow to a rapid flash
light. Then release both buttons.

Some entry gates and garage
door openers may require
substitution of Step 2 with the
procedure under

“

Programming

for Some Gate Operators

”

later in

this section.

3. Press and hold the newly

programmed Universal Remote
system button for five seconds
while watching the indicator
light and garage door activation.

.

If the indicator light stays on
continuously or the garage
door moves when the button
is pressed, then programming
is complete. There is no need
to complete Steps 4

–

6.

.

If the indicator light does not
come on or the garage door
does not move, a second
button press may be
required. For a second time,

«
...
142
143
144
145
146
...
»

Содержание Escalade 2020




































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Escalade 2020

2011 Corolla LE

Бренд: Toyota Страницы: 19

Бренд: Yakima Страницы: 12

Бренд: V8 equipment Страницы: 17

Бренд: Phonocar Страницы: 2

Automotive 31006

Бренд: KRAFTWERK Страницы: 2

Бренд: FAAFTECH Страницы: 8

Бренд: AutoMaxi Страницы: 2

Бренд: Atera Страницы: 10

4500 CHASSIS CAB 2012

Бренд: RAM Страницы: 7

Бренд: Cadillac Страницы: 20

BASIC TLL171231

Бренд: Tellur Страницы: 5

Бренд: E&G Classics Страницы: 3

Бренд: Skoda Страницы: 281

Бренд: S3 Power Sports Страницы: 2

2004 Impreza OUTBACK SPORT

Бренд: Subaru Страницы: 34

Бренд: Acura Страницы: 6

Бренд: Thule Страницы: 4

Бренд: r.LiNK Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды