Butterfly BECS-528 Скачать руководство пользователя

Страница: 7 / 130

Chapter 1 General Descriptions

BECS-528 Computerized Embroidery Machine's Manual

Installation

Caution

Don't jam the vent on the device. Don’t plug up the machine, or it may set

fire.

Caution

Make sure the installing direction is correct..

Caution

Don't install the machine to the position with wet gas, corrosive gas,

flammable gas and explosive gas

Cable Connection

Forbidden

Don't test the insulation of the circuit loop.

Forbidden

Never try to connect overloaded electronic device on the connector..

Caution

Make sure the insulation cover of the cable is fine.

Caution

Signal cable and power cable should be separated.

Caution

All the cables should be well fixed. Don’t put any strength on cables. Make

sure the turning point of cable is well protected. Add pipes to increase

insulation capability.

Caution

Machine should be grounded. The resistance should be no larger than 10

Operation Direction

Danger

Don't operating the machine when there is any damage on the protection

cover

Forbidden

When machine is running, do not touch any running part.

Caution

Make sure the configuration of power supply is normal. Use stabilized

power supply (with grounding device) when the voltage waves beyond the

normal range at -10%~10%.

Caution

In case of warning, please check out the problem. Operation can only be

carried out again when problem is solved.

Caution

The power supply has over-currency protection function. There is a 3 mins

time lag before the switch can be closed again.

Maintenance

Содержание BECS-528



































































































































Результаты поиска

Содержание BECS-528

Отзывы:

Похожие инструкции для BECS-528

Бренды по названию

Популярные бренды

Butterfly BECS-528, Руководство пользователя

Результаты поиска

Содержание BECS-528

Отзывы:

Похожие инструкции для BECS-528

Бренды по названию

Популярные бренды