Butterfly BECS-528 Скачать руководство пользователя

Страница: 130 / 130

Appendix

Ⅳ

Network Connection of Embroidery

Machines

BECS-528 Computerized Embroidery Machine's Manual

125

Network

Network number

Computer number

1 192.168.1

2 192.168.2

(3)

Subnet mask

To show how the network number and computer number are divided, subnet mask is

used to tell in one IP address which part is for network and which part is for computer. It’s

regulated that “1” is for network part and “0” is for computer part. IP address and subnet

mask combine to tell in which network the computer is. So the subnet mask is very

important. If it’s wrong, it will get the wrong network address. Therefore the same network

number must be set with the same subnet mask.

(4)

Gateway

It’s the IP address of the router which is in the same subnet of the computer. As in the

followed picture, if one data packet is to be transmitted to a computer in network 2, this

data packet has to be sent to the router linked to us. It’s like in sending by post you only

need to deliver a letter to postman instead of delivering by yourself. So when the computers

are not in the same network segment, the gateway also has to be set properly in setting

computers. Otherwise computers don’t know where to deliver the data packet.

Содержание BECS-528



































































































































Результаты поиска

Содержание BECS-528

Отзывы:

Похожие инструкции для BECS-528

Бренды по названию

Популярные бренды

Butterfly BECS-528, Руководство пользователя

Результаты поиска

Содержание BECS-528

Отзывы:

Похожие инструкции для BECS-528

Бренды по названию

Популярные бренды