Butterfly BECS-528 Скачать руководство пользователя

Страница: 22 / 130

Chapter 3 How to Start Embroidery

BECS-528 Computerized Embroidery Machine's Manual

(2)

In the main picture, the icon "

" appears and the machine enters into the

embroidery confirmation status. Then, user can pull the bar to start embroidery. If

pressed, the machine will be in the embroidery release mode. At this moment, the machine will

not run even user pulls the bar. Beside that, the system will hint user to confirm the

embroidery.

3-5 Normal Embroidery, Returning and Mending Embroidery

In embroidery confirmation status (the icon "

" appears), push the mending switch of

machine head that will perform normal embroidery to go to the normal embroidery mode, and

push the mending switch of machine head that will not embroider go to the mending mode, and

then pull the operation bar to right and release it to let the machine start normal embroidery.

(When you pull the bar to right and don't release it, the machine will embroider in lower speed.)

During embroidery, pull the bar to left, the machine will stop.

After the machine stops, pull the operation bar to left and the frame will return to its last

position along original path. Pull the bar one time, the frame return one needle step. Pull the

bar continuously and the frame will return one needle step after another continuously. After the

frame return 10 needle steps continuously, the frame can return continuously even when you

release the bar.( This may be different according to different machine types). When the frame

return continuously, release the bar and pull the bar to the left again, the frame will stop

returning.

The aim of returning is usually to perform mending embroidery. After the returning stops,

push the mending switch of machine head that will perform mending embroidery to go to the

mending mode, and then pull the operation bar to right and the machine head will start

mending embroidery while other heads keep still. When the frame goes to the point where the

frame begins to return, other heads whose mending switches are in normal embroidery mode

will start embroidery.

3-6 Release

Embroidery

Confirmation Status

You should release embroidery confirmation status when you want to embroider other

patterns after finishing the embroidery of one pattern or to revise size ratio, rotating angle, the

repetition, figure direction, or to do the operation of "Disk Management" and "Design

Management".

Содержание BECS-528



































































































































Результаты поиска

Содержание BECS-528

Отзывы:

Похожие инструкции для BECS-528

Бренды по названию

Популярные бренды

Butterfly BECS-528, Руководство пользователя

Результаты поиска

Содержание BECS-528

Отзывы:

Похожие инструкции для BECS-528

Бренды по названию

Популярные бренды