Butterfly BECS-528 Скачать руководство пользователя

Страница: 14 / 130

Chapter 2 Names of Parts on Electrical Control System

BECS-528 Computerized Embroidery Machine's Manual

automatically. In the event that the machine has no trimming device or, user can trim the thread

manually when the machine stops at embroidery.

Manual Trimming: This function can trim the thread via the keyboard even when the

machine stops. In the main interface press "

" key to display the hint window, where user

can move the icon to select the trimming method (“Up & Bottom Thread” or “Bottom Thread”),

Press "

" key to trim thread or press

“

”

key to quit.

2-3 Operation Bar and Turn Shaft Button

Operation bar (embroidery bar under the table)

Stop status: pull the bar to right to begin embroidery (including idle running in high or

low speed) and pull the bar to left to return (including idle running in high or low speed)

Running status: pull the bar to right to the end to embroider slowly and release to normal

speed and pull the bar to left to stop embroidery.

Turn Shaft Button(over the operation bar case, on the right under the table)

To press the button to make the main shaft rotate one cycle and stop at 100

2.5

2-4 Mending

Switch

Thread Breakage Detection Device of 3 places

There is a switch on every head of machine. When the switch is up, this head is in normal

embroidery mode; when it is in the middle, this head is in mending mode; and when it is down

this head is in stop mode.

Thread Breakage Detection Device of 2 places

On every head of the machine, there is a mending switch, and it can be moved with hand

to the up, middle or down position, but it can only stop at the middle or down position. When

the switch is pushed to up position, the lamp is red, which hints that this head is in mending

mode. In addition, while thread breaks during embroidery, the lamp is automatically changed

to red and this head will turn to mending mode. When the switch is at middle position, this

head is in mending mode if the lamp is red, or this head is in normal embroidery mode if the

lamp is green. When the switch is pushed to down position, the lamp is off, which hints that

this head is in stop mode. When the switch is pushed to middle position from down position,

the lamp will be green and the head is in normal embroidery mode.

Содержание BECS-528



































































































































Результаты поиска

Содержание BECS-528

Отзывы:

Похожие инструкции для BECS-528

Бренды по названию

Популярные бренды

Butterfly BECS-528, Руководство пользователя

Результаты поиска

Содержание BECS-528

Отзывы:

Похожие инструкции для BECS-528

Бренды по названию

Популярные бренды