BUSCH COBRA BC 0600 F, Инструкция по установке и обслуживанию

Страница: 10 / 24

Information over the lubricants
Oil
Busch YLC 250 B, Art. No. 0831 000 054 (0,5 l
@
1 kg)
Quantity BC 0600 F :
–
WY 0700 C-MB: 1,4 l
–
NW 0100 E-DP: 0,12 l
Replacement: After 16'000 h (see Maintenance program)
Technical data sheet: Please refer to chapter "Oil type/ Quantity".
Decommissioning procedure
When the product arrives at the end of the lifetime, it is necessary to
proceed to the decontamination of the vacuum pump
WARNING
Any disassembly of the vacuum pump should only be carried out by
staff trained for this purpose. Before disassembly, the user of the
vacuum pump should complete a form or “Declaration about
absence of danger” which indicates any dangers and corresponding
actions.
Without this form duly completed and signed by a legally responsi-
ble person, the pump should not be disassembled.
l Proceed to disassembly of the vacuum pump. Please make sure to
wear a personal protective equipment (PPE) prior to any interven-
tion on the vacuum pump. Some residue may remain inside.
l Proceed to decommissioning of the different parts according to the
current local and national laws
Transport
The COBRA BC vacuum pumps are tested and checked in our factory
before careful packing. Check the packaging for transport damage
when the goods arrive. The pump can withstand temperatures
between -25°C and +55°C during transport.
Transport in packed state
Packed on a pallet, the vacuum pump can be moved with a hand
forklift truck.
Transport in unpacked state
The vacuum pump is fastened to the pallet with fixing pins:
u Unscrew the fastening nuts underneath the pallet.
CAUTION
Do not work, walk or stand under suspended loads.
CAUTION
Please check out the weight of the vacuum pump before lifting it up
(see "Technical Data").
Use adequate lifting gear for this.
NOTE : The eyebolts are fitted more or less at equal distance from the
centre of gravity of the vacuum pump incl. drive motor. If any accesso-
ries that could upset the balance of the vacuum pump, are installed, or
if the vacuum pump is delivered without drive motor, it is necessary to
add a belt or rope at a suitable point when lifting the pump.
l Attach lifting gear securely to the eyebolt or eyebolts
l Use lifting gear with a crane hook equipped with safety latch.
l Lift the vacuum pump
In case the vacuum pump was bolted to a pallet with fixing bolts:
Unscrew the fixing bolts in the base frame.
CAUTION
In case of a vacuum pump filled with oil, make sure that by lifting
the inclination angle of the vacuum pump do not exceed 5° from
the horizontal . In case of too high inclination (>5°), risk of oil leak
within the work area.
Make sure before every transport using the appropriate lifting mean
that the inclination of the vacuum pump is less than 5°.
The packaging material must be disposed of in accordance with local
and national regulations.
This handbook is contained in the delivery package.
Storage
Temporary storage
l Make sure that the intake and exhaust flanges are closed (put on
the protective caps included in the delivery package of the vacuum
pump)
l Store the vacuum pump
–
if possible, the vacuum pump should be stored in its original pac-
kaging,
–
indoors,
–
dry,
–
in a dust-free and vibration-free room
Removal of the pump
Before starting a vacuum pump that has been stored outside the buil-
ding for a while, the vacuum pump must be moved to a room with
ambient temperature, where it should rest for a day.
Preservation
If the vacuum pump will be exposed to unfavourable ambient condi-
tions (for example, aggressive environment, frequent temperature
changes), begin immediately with preservation work on the vacuum
pump.
In the case of favourable ambient conditions, perform preservation
work on the vacuum pump if a storage period of more than three
months are planned.
l Make sure that all openings are hermetically sealed; use adhesive
tape to fasten loose parts (seal rings, flat seals, etc.).
Transport BC 0600 F
Page 10
0870767449 (En)