Buderus Logano GC124 II/SP Скачать руководство пользователя страница 17

Страница: 17 / 84

Boiler installation

We reserve the right to make any changes due to technical modifications.

Installation and maintenance instructions Gas Boiler Logano GC124 II/SP • Issue 07/2006

Description of field installed wiring connections
using factory supplied junction box.

Remove two knock-outs from the left side of boiler
panel to route electrical feed and pump power into
junction box.

Route electrical power from the outside into junction
box.

Install a metal strain relief for the incoming power line
on outside of left boiler jacket panel. (

Fig. 12).

Just use supplied wiring nuts and double proper wir-
ing before powering up the boiler.

Check that the heating system functions correctly af-
ter any maintenance work.

Fig. 11

Electrical junction box

Electrical junction box (Inside of jacket cabinet)

Incoming line voltage wiring

Furnished wiring nuts.

USER NOTE

When making the electrical connections
use only wires that are approved for elec-
trical use.

USER NOTE

Refer to the wiring diagrams on pages

page 80 bis

page 82 for electrical

details.

Fig. 12

Strain relief for shielded electrical wiring

WARNING!

RISK TO LIFE

from electrical shock.

When conducting maintenance work
label all cables before disconnecting
them.

If cables are connected incorrectly the
system may not operate correctly with
possibly dangerous consequences.

WARNING!

FIRE DANGER

Hot boiler components may damage elec-
trical wiring.

Make sure that all cables are routed in
the ducts or on the boiler insulation.

Содержание Logano GC124 II/SP





















































































Результаты поиска

Содержание Logano GC124 II/SP

Отзывы:

Похожие инструкции для Logano GC124 II/SP

Бренды по названию

Популярные бренды

Buderus Logano GC124 II/SP, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logano GC124 II/SP

Отзывы:

Похожие инструкции для Logano GC124 II/SP

Бренды по названию

Популярные бренды