Buderus Logano GC124 II/SP Скачать руководство пользователя страница 11

Страница: 11 / 84

Moving the boiler

We reserve the right to make any changes due to technical modifications.

Installation and maintenance instructions Gas Boiler Logano GC124 II/SP • Issue 07/2006

Set the boiler cart or dolley on the front side of the
boiler and put a piece of cardboard between the two
to prevent scratches.

Secure boiler on the boiler cart.

Move boiler to desired location.

Place the boiler at its final postion.

5.2

Lifting and carrying the boiler

The boiler can be picked up at the both long sides of the
boiler as shown.

Fig. 5

Moving the boiler with dolley or boiler cart.

Additional card board for protection.

CAUTION!

RISK OF INJURY

due to improper securing of the boiler dur-
ing transport.

Use a boiler coart or dolley and strap
for moving the boiler

Secure boiler on the boiler cart.

Remove the front door during lifting or
transport to prevent unintentional open-
ing.

Fig. 6

Lifting and carrying the boiler

7 747 000 511-04.0K

CAUTION!

RISK OF INJURY

due to carrying heavy loads.

Lift and carry the boiler with at least four
people at the designated side panel lo-
cations.

Содержание Logano GC124 II/SP





















































































Результаты поиска

Содержание Logano GC124 II/SP

Отзывы:

Похожие инструкции для Logano GC124 II/SP

Бренды по названию

Популярные бренды

Buderus Logano GC124 II/SP, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logano GC124 II/SP

Отзывы:

Похожие инструкции для Logano GC124 II/SP

Бренды по названию

Популярные бренды