Buderus Logano GC124 II/SP Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 84

background image

14

Installation and maintenance instructions Gas Boiler Logano GC124 II/SP • Issue 07/2006

We reserve the right to make any changes due to technical modifications.

Boiler installation

7

7.2

Connecting the heating system

Fig. 8

Low-water cut-off installation

1

Boiler

2

Radiator

3

Heating system with low-water cut-of

4

Heating system without low-water cut-off

1

2

2

1

2

2

2

2

3

4

CAUTION!

BOILER DAMAGE

Due to moisture.

z

Protect the components of the gas igni-
tion system from moisture (dripping,
spray, rain) during installation of the
boiler, during operation and during
maintenance work (such as replacing
the pump, replacing the control, etc.).

CAUTION!

SYSTEM DAMAGE

Due to overheating as a result of a low wa-
ter condition.

z

Note that a boiler installed above the
level of the heating system must be
equipped with a low-water cut-off. The
low-water cut-off must be installed dur-
ing installation of the boiler and placed
above the water level in the boiler with-
out any means of shutting the water off
between the boiler and low water
cut-off (

Î

Fig. 8).

CAUTION!

SYSTEM DAMAGE

Due to high temperature variations in the
heating system.

z

If the boiler is operated in connection
with a refrigeration system, make sure
that the pipes for the refrigerated liquid
are connected in parallel to the boiler
system with suitable valves to prevent
the refrigerated liquid from entering the
boiler.

z

The piping system of a boiler connect-
ed to the heating coils of hydro-air heat-
ing systems that may be exposed to the
circulation of cooled air must be
equipped with a flow-control valve or
some other automatic system for pre-
venting the boiler water from circulating
by gravity during the cooling cycle.

«
...
12
13
14
15
16
...
»

Содержание Logano GC124 II/SP





















































































Отзывы:

Нет отзывов

Похожие инструкции для Logano GC124 II/SP

Бренд: Harsco Industrial Страницы: 58

Бренд: IBC Страницы: 4

Бренд: Garland Страницы: 40

Condexa Pro 100 P

Бренд: Riello Страницы: 23

ecoTEC pure VC 146/7-2(E-DE)

Бренд: Vaillant Страницы: 48

Бренд: Bryan Boilers Страницы: 4

Бренд: Bryan Boilers Страницы: 36

Бренд: Brute Страницы: 100

Benchmark BMK 1000

Бренд: Aerco Страницы: 178

Бренд: croydon Страницы: 2

Бренд: croydon Страницы: 2

Бренд: Baxi Страницы: 20

BRAVA One HE 25

Бренд: Sime Страницы: 108

TEK Biomasse PIKO

Бренд: VM Страницы: 48

Benchmark BMK 1000

Бренд: Aerco Страницы: 192

Бренд: Anvil Страницы: 1

Бренд: Anvil Страницы: 1

Bryan DR Series

Бренд: Bryan Boilers Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды