Buderus Logano GC124 II/SP Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 84

background image

Boiler inspection and maintenance

16

57

We reserve the right to make any changes due to technical modifications.

Installation and maintenance instructions Gas Boiler Logano GC124 II/SP • Issue 07/2006

16.9 Troubleshooting the GC124 SP

Equipment required: Wiring diagrams (

Î

Chapter 19, page 80) and voltage detectors for 120 VAC and 24 VAC.

•

Verbindungen zur Gasarmatur prüfen.

•

Geht die Zündflamme aus, prüfen, ob das Thermoelement dicht mit den
Gasventilen abschließt; wenn ja Thermoelement austauschen.

•

Geht die Zündflamme immer wieder aus, Gasventile austauschen.

•

Prüfen, ob alle handbetätigten Gasabsperrventile geöffnet, Gasan-
schlüsse und Druckmesswerte in Ordnung und Zündgasdüsen nicht ver-
stopft sind.

•

Check connections to gas valve.

•

If the ignition flame goes out, check that the thermocouple is firmly
screwed to the gas valve; if yes, replace thermocouple.

•

If the ignition flame continues to go out, replace gas valve.

•

Check that all manually operated gas shut-offs are open; check that gas
connections and pressures are correct and that pilot orifice is not blocked.

Start

Set gas valve ON/OFF knob
clockwise to OFF position.
Close main gas shut-off. Set
thermostat (control) to heat re-
quirement (vent damper
opens).
Switch on power.

Set gas valve ON/OFF knob
counterclockwise to PILOT posi-
tion. Open main gas shut-off.
Press red pilot ignition button
and ignite ignition flame. Hold
down red pilot ignition button for
one minute and then release. Ig-
nition flame is burning.

•

Check electrical power source, low-voltage transformer, thermostat (con-
trol) and wiring. Check that the vent damper is open and the limit switch
is present.

No

No

No

Set gas valve ON/OFF knob
counterclockwise to ON. Main
burner ignites.

•

Check 24-V voltage at the gas valve.

•

Check electrical connections to gas valve. If OK replace gas valve.

No

System operates until the heat
requirement ends.

•

Check that the ignition flame surrounds the thermocouple and burns
evenly with a bluish flame. If OK replace thermocouple.

No

Heat requirement ended, sys-
tem switches off, vent damper
closes. Ignition flame continues
to burn.

•

Check operation of thermostat (control).

•

Disconnect 24-V connection to gas valve. If gas valve closes, check ther-
mostat and electrical wiring again.

•

If the gas valve does not close, replace gas valve.

End of troubleshooting

Repeat procedure until heating system operates properly.

«
...
55
56
57
58
59
...
»

Содержание Logano GC124 II/SP





















































































Отзывы:

Нет отзывов

Похожие инструкции для Logano GC124 II/SP

Бренд: Harsco Industrial Страницы: 69

Бренд: A.O. Smith Страницы: 56

Бренд: Calomax Страницы: 10

Бренд: Calomax Страницы: 24

Бренд: Daikin Страницы: 24

Aerco Modulex EXT Series

Бренд: Watts Страницы: 144

Бренд: STIEBEL ELTRON Страницы: 60

Бренд: Bakers Pride Страницы: 18

Бренд: Camus Hydronics Страницы: 90

Бренд: Ataq Страницы: 16

Бренд: Bosch Страницы: 44

Worcester GR8700iW 30 S NG

Бренд: Bosch Страницы: 80

Buderus SB625WS

Бренд: Bosch Страницы: 52

Worcester GB162-100 V2

Бренд: Bosch Страницы: 52

Бренд: Bosch Страницы: 32

Бренд: Bosch Страницы: 16

Бренд: Bosch Страницы: 36

Бренд: Bosch Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды