Buderus Logano GC124 II/SP Скачать руководство пользователя страница 45

Страница: 45 / 84

Boiler inspection and maintenance

We reserve the right to make any changes due to technical modifications.

Installation and maintenance instructions Gas Boiler Logano GC124 II/SP • Issue 07/2006

16.5 Cleaning the boiler

The boiler can be cleaned with brushes and/or by wet
cleaning. Cleaning tools are available as accessories.

Inspecting the ignition burner of the GC124 II

Observe the ignition burner through the sight glas
(

Fig. 39).

The flame must rise over the sensor by ½" to 1-½".

The pilot ignition gas pressure must be adjusted if
the flame is too small or too large.

Fig. 39

GC124 II boiler

Sight glass

Fig. 40

Correct ignition flame setting

Flame rises ½" to 1-½" above sensor

Ignition flame

USER NOTE

The adjustment screw is located behind a
safety screw on the gas valve (

Fig. 41,

page 46).

Содержание Logano GC124 II/SP





















































































Результаты поиска

Содержание Logano GC124 II/SP

Отзывы:

Похожие инструкции для Logano GC124 II/SP

Бренды по названию

Популярные бренды

Buderus Logano GC124 II/SP, Инструкция по установке и обслуживанию

Результаты поиска

Содержание Logano GC124 II/SP

Отзывы:

Похожие инструкции для Logano GC124 II/SP

Бренды по названию

Популярные бренды