U.S. Boiler Company ALTAC-200 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 100

background image

110327-04 - 1/22

ALTA

• Combi Boiler/Water Heater

• Condensing

• Direct Vent

• Gas Fired

Models:
• ALTAC-136
• ALTAC-200

WARNING

This boiler must only be installed, serviced, or repaired by a qualified installer, service agency or gas supplier.

Improper installation, adjustment, alteration, service or maintenance can cause severe personal injury, death,

or substantial property damage. For assistance or additional information, consult a qualified installer, service

agency, or the gas supplier. Read these instruction carefully before installing.

!

Installation, Operating and Service Instructions for

Manual Contents   Page
1.  Installer Read Before Proceeding  . . . . . . . . . . .3
2. Homeowner Read Before Proceeding . . . . . . . .5
3. Specifications  . . . . . . . . . . . . . . . . . . . . . . . . . . .6
4.   How It Works  . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
5.   Locating Boiler  . . . . . . . . . . . . . . . . . . . . . . . . .10
6.   Preparing Boiler  . . . . . . . . . . . . . . . . . . . . . . . .14
7.   General Venting  . . . . . . . . . . . . . . . . . . . . . . . . .17
8.    Sidewall Direct Venting . . . . . . . . . . . . . . . . . . .24
9.   Vertical Direct Venting   . . . . . . . . . . . . . . . . . . .30
10.  Heating System Piping  . . . . . . . . . . . . . . . . . . .36
11.  Domestic Water Piping  . . . . . . . . . . . . . . . . . . .39
12.  Gas Piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
13.  Field Wiring   . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
14.  Condensate Disposal  . . . . . . . . . . . . . . . . . . . .46
15.  Start-up and Checkout    . . . . . . . . . . . . . . . . . .47
16.  Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
17.   Before Leaving Jobsite   . . . . . . . . . . . . . . . . . .65
18.  Service and Maintenance  . . . . . . . . . . . . . . . . .66
19.  Troubleshooting   . . . . . . . . . . . . . . . . . . . . . . . .71
20.  Internal Wiring Diagrams   . . . . . . . . . . . . . . . . .86
21.   Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . .89
Appendix
  A. Combination Refrigeration/Heating System  . .95
B. Water Quality and Boiler Additives  . . . . . . . . .96
C. Special Requirements In Massachusetts  . . . .97
D. Code Required Text  . . . . . . . . . . . . . . . . . . . . . .99

TO THE INSTALLER:

Affix these instructions adjacent to boiler.

Provide model number and serial number when

seeking information and support.

TO THE HOMEOWNER:

Retain these instructions for future reference.

Contact heating installer or technician for all issues

and support.

Version en Español disponible en el web del fabricante.

www.usboiler.net

1
2
3
...
»

Содержание ALTAC-200





































































































Отзывы:

Нет отзывов

Похожие инструкции для ALTAC-200

Бренд: Garanterm Страницы: 20

VOGUE COMBI GEN2 C26

Бренд: Ideal Boilers Страницы: 80

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 47

Бренд: Keston Страницы: 8

VortexBlue VTXBF21

Бренд: Grant Страницы: 68

Planet Dewy 100 BFR

Бренд: Sime Страницы: 40

Бренд: Beretta Страницы: 60

Бренд: Kober Страницы: 17

Бренд: Kober Страницы: 18

Бренд: Kober Страницы: 28

Бренд: Blodgett Страницы: 2

Бренд: Magikitch'n Страницы: 15

Бренд: STIEBEL ELTRON Страницы: 16

Heatpac 12-18kW

Бренд: FireBird Страницы: 36

Бренд: HTP Страницы: 8

SuperStor Ultra SSU-20B

Бренд: HTP Страницы: 8

AQUA HE 25 ErP BE

Бренд: Sime Страницы: 96

Mini-Boiler EMB-S-1

Бренд: Electro Industries Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды