U.S. Boiler Company ALTAC-200 Скачать руководство пользователя страница 79

Страница: 79 / 100

110327-04 - 1/22

ALTA

Combi Installation, Operating & Service Instructions

Table 19-5: Active Fault Code and Corrective Actions (continued)

Detailed Fault Code found on "

" and "

" menus in brackets, e.g. [

Code

Name

Possible Cause

Corrective Action

E15

APS

Defective

(failed to

open)

Defective air proving

switch, failed to open.

• Remove jumper from air proving switch.

• Check switch, tube connection, and wiring. Check tube is

connected and unobstructed. Replace if necessary.

The blower is running

when it should not.

Blower is running before start sequence. This can be caused

by a loss of communication between blower and control,

resulting in blower going to max speed. Possible cause is a

defective wiring harness, blower or control.

H16
E16

Low

Combustion

Air Flow

Air flow is blocked.

Check vent, air inlet, heat exchanger and burner. Remove

obstruction.

Defective air proving

switch.

Check switch, tube connection and wiring. Check tube is

connected and unobstructed. Replace if necessary.

Blower Fault

Check blower, blower power, control and wiring to blower.

Troubleshooting

(continued)

Code

Name

Possible Cause

Corrective Action

H18
E18

Invalid

Application

Parameters

[

] Application

parameters are not valid.

Normal condition following a parameter download, set Factory

Defaults, parameter

A10

. (Table 16-11, Menu

, Quick Menu)

[

] Parameter Model

Mismatch.

Repeat reset to factory default using parameter

A10

. If problem

persists, replace control.

[

] CH Setpoint and

Modulation source both

selected.

(Feature not available with local user display). Only CH

Setpoint or Modulation source may be selected. Select only

a single feature. Check Central Heat Modulation Rate Source

and Central Heat Setpoint Source.

[

] Invalid header

sensor configuration.

(Feature not available with local user display). Header/

Recirculation Sensor selection must be set to "Header" when

selecting CH modulation sensor selection to "Header".

[

] Invalid Stepped

modulation parameters

(Start Offset Recycle

Limit)<5°F (3

C).

(Feature not available with local user display). Check Stepped

Modulation Start Offset is 5°F (3°C) greater than Stepped

Modulation Recycle offset. Check Flow and Flue temperature

Stepped Modulation Start Offset is 5°F (3°C) greater than Flow

and Flue temperature Stepped Modulation Recycle Offset.

[

] Invalid Setpoint

interpolation parameters.

(Feature not available with local user display). Check CH

20 mA Water Temperature is greater than CH 4 mA Water

Temperature.

[

] Invalid Comfort

Mode configuration.

(Feature not available with local user display). Comfort mode

selected and Header/Recirculation Sensor selection is not set

to "Recirculation" or Auxiliary thermostat input selection not set

to "Recirculation Enable".

[

] Factory defaults not

turned on.

Ensure BCC is installed and select

A10

factory Default "On"

(Table 16-11).

[

] Pump mismatch.

Boiler pump set to 0 or boiler pump output set to 3 and Aux.

pump ouput is not set to 3.

E19

Gas Valve Or

Blower Fault

Air fuel ratio is persistently

outside acceptable limit.

Check wiring to gas valve and blower. If wiring is OK, replace

blower and retry. If blower OK, replace gas valve and retry.

H20
E20

Ignitor/Flame

Sensor or

Burner Fault

Ignitor/flame sensor wiring

issue.

Check the ignitor/flame sensor wiring and earth contacts at

burner.

Dirty or damaged ignitor/

flame sensor.

Check and correct ignitor/flame sensor gap and distance to

burner. Replace if necessary.

Dirty/ damaged burner.

Check burner. Replace burner if necessary.

H21
E21

Gas Valve

Fault

No gas, insufficient gas

supply pressure.

Verify no air in gas line. Check gas supply pressure.

Check gas valve inlet pressure during operation.

Defective gas valve.

Check gas valve inlet pressure during operation and check

wiring to gas valve.

If problem persists, replace gas valve.

If problem persists, replace control.

[

E21

] Gas valve wiring

problem.

Table 19-5: Active Fault Code and Corrective Actions (continued)

Detailed Fault Code found on "

" and "

" menus in brackets, e.g. [

Содержание ALTAC-200





































































































Результаты поиска

Содержание ALTAC-200

Отзывы:

Бренды по названию

Популярные бренды

U.S. Boiler Company ALTAC-200, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание ALTAC-200

Отзывы:

Бренды по названию

Популярные бренды