Brother GT-3 Series, Руководство по обслуживанию

Страница: 4 / 375

CAUTION
Installation
Setting up and moving of the printer should only be
carried out by a qualified technician.
The printer machine weighs approximately 111 kg
(245 lb). Transporting and setting up of the printer
should be held in proper way.
The machine may fall down and cause injury.
The printer must be used on a suitable stable
surface, otherwise it may tip over or fall down and
cause injury.
Furthermore, the table that supports the printer
should be at least 137 cm (53.9 inch) in width and
104.5 cm (41.1 inch) in depth, and should be able to
bear a weight of 150 kg (330 lb) or more.
Do not set up the printer in a place where it will be
affected by vibration. It may become unbalanced
and fall down, which cause injury or damage to the
printer.
Do not connect the power cord until setup is
complete, otherwise the printer may operate if the
power switch is turned on by mistake, which could
result in injury.
Do not climb onto the printer or place heavy objects
on top of it, otherwise it may become unbalanced
and tip over or fall down and cause injury.
Printing
This printer should only be used by operators who
are appropriately trained in its operation.
Ensure there is adequate space left for safe working.
The Platen moves forward while operating and it
may be injured.
Do not handle the platen while printing. If your hand
gets caught between the platen or the T-shirt tray
and the covers, it may be injured.
Do not move the Platen by hand.
The Printer may be mechanically and electrically
damaged.
Do not put your hands inside the covers while the
printer’s power is turned on, otherwise your hands
may touch against moving parts and this may result
in injury.
When a problem occurs with the operation of the
printer, contact the place of purchase or a qualified
technician.
Maintenance
Wait at least 1 minute after turning off the power
switch before opening the front cover.
Do not touch the head heat sink as it may be HOT
and may cause a burn.
Be careful not to get your fingers caught when
closing the front cover, otherwise it may result in
injury to your fingers.
Do not move the Platen by hand.
The Printer may be mechanically and electrically
damaged.
Do not disassemble the ink cartridge.
Disassembly, assembly, maintenance and inspection
of this printer should only be carried out by qualified
technicians.
Ask your Brother dealer or a qualified electrician to
carry out any maintenance and inspection of the
electrical system.
Turn OFF the power switch and disconnect the
power cable before carrying out the following
operations. The printer may start operating if
incorrectly operated, resulting in possible injury.
- Inspection, adjustment or repair
Turn OFF the power switch before plugging in or
removing the power cord.
Failure to observe this may result in Control Box
malfunction.
Always return any removed safety protection devices
to their original location, and ensure that they are
functioning normally.
Take care not to let the liquids: Ink, Wash Liquid,
Maintenance Solution, Pretreatment or waste liquid
come into contact with your eyes or onto your skin,
otherwise inflammation can result. In case of contact
with eyes, do not rub but immediately rinse the eyes
with water.
Furthermore, do not drink the liquids: Ink, Wash
Liquid, Maintenance Solution, Pretreatment or waste
liquid under any circumstances, as they can cause
vomiting and diarrhea.
Keep the liquids out of the reach of children
.
Be sure to wear protective goggles and gloves when
handling the grease, so that they do not get into
your eyes or onto your skin. If the grease gets into
your eyes or onto your skin, inflammation can result.
Furthermore, do not drink or eat the grease. They
may cause diarrhea or vomiting.
Keep the grease out of the reach of children.
When replacing parts and installing optional
accessories, be sure to use only genuine Brother
parts.
Brother will not be held responsible for any
accidents or problems resulting from the use of
non-genuine parts.
GT-3 Series
iii