Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 176

background image

swDir:admin>

2. (Optional) Modify passwords. To skip modifying the password, press

Ctrl+C

. For more information

on passwords, refer to the

Fabric OS Administrator's Guide

.

NOTE

Passwords can be 8 to 40 characters long. They must begin with an alphabetic character. They can
include numeric characters, the period (.), and the underscore (_) only. Passwords are case-
sensitive, and they are not displayed when you enter them on the command line. For more
information on passwords, refer to the

Fabric OS Administrator's Guide

.

Configuring the IP addresses

The Brocade DCX 8510-8 requires three IP addresses, which are configured using the

ipAddrSet

command. IP addresses are required for both CP blades (CP0 and CP1) and for the chassis
management IP (shown as SWITCH under the

ipAddrShow

command) in the Brocade DCX 8510-8.

NOTE

The default IP addresses and host names for the Brocade DCX 8510-8 are:

• 10.77.77.75 / CP0 (the CP blade in slot 6 at the time of configuration)
• 10.77.77.74 / CP1 (the CP blade in slot 7 at the time of configuration)

NOTE

Resetting an IP address while the Brocade DCX 8510-8 has active IP traffic or has management and
monitoring tools running, such as DCFM, Fabric Watch, and SNMP, can cause traffic to be interrupted
or stopped.

Complete the following steps to set the IP addresses for the Brocade DCX 8510-8.

1. Log in to the active CP as admin using the serial cable connection.
2. Set up the Brocade DCX 8510-8 IP address by entering the

ipaddrset -chassis

command:

swDir:admin> ipAddrSet -chassis

Enter the information at the prompts. Specify the

-chassis

IP address. The

-sw 0

IP address is not

valid on this chassis.

NOTE

The addresses 10.0.0.0 through 10.0.0.255 are reserved and used internally by the Brocade DCX
8510-8. External IPs must not use these addresses.

3. Set up the CP0 IP address by entering the

ipaddrset -cp 0

command:

swDir:admin> ipAddrSet -cp 0

Enter the information at the prompts.

4. Set up the CP1 IP address by entering the

ipaddrset -cp 1

command:

swDir:admin> ipAddrSet -cp 1

Configuring the IP addresses

38

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

«
...
36
37
38
39
40
...
»

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCX 8510-8

Serial Servers Vlinx VESR9xx

Бренд: B&B Electronics Страницы: 61

iDataPlex dx320 6385

Бренд: IBM Страницы: 60

SuperWorkstation 740A-T

Бренд: Supermicro Страницы: 138

System x3650 M4 BD Type 5466

Бренд: IBM Страницы: 786

E7210 Master-FARM

Бренд: MSI Страницы: 34

Past Ethernet Combo Print Server PS-1216U

Бренд: Edimax Страницы: 23

Бренд: Fujitsu Страницы: 200

Firepower Management Centers

Бренд: Cisco Страницы: 20

Бренд: Cisco Страницы: 34

MCS-7825-H1-IPC1

Бренд: Cisco Страницы: 54

Бренд: Cisco Страницы: 62

Бренд: Cisco Страницы: 10

KIN-UCSM5-1RU-K9

Бренд: Cisco Страницы: 22

Бренд: Cisco Страницы: 3

Cisco MeetingPlace Express

Бренд: Cisco Страницы: 20

Бренд: Cisco Страницы: 88

Бренд: Cisco Страницы: 14

Бренд: Cisco Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды