Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя

Страница: 102 / 176

}

5. Login to the chassis and execute the

switchcfgpersistentdisable

command on the main switch

and other logical switches. The

switchcfgpersistentdisable

command disables the switches, and

ensures they remain disabled after the power is cycled. This allows you to check all the settings so
that you can verify the settings before placing the chassis back into production.

switch:FID128:root> switchcfgpersistentdisable

Switch's persistent state set to 'disabled'

switch:FID128:root>

If there are other logical switches on your chassis, use the

setcontext

command to connect to all

the other switches and then run

switchcfgpersistentdisable

on these switches as well.

6. Power down the entire chassis.
7. Remove the screws from the WWN bezel on the back of the chassis. Pull the bezel away from the

chassis and set it aside. The two WWN cards are now visible.

8. Use a Phillips screwdriver to unscrew the screws that secure each WWN card to the chassis. Label

the WWN cards and cables with #1 for the left side and #2 for the right side, for future reference.

9. Disconnect the WWN cable by depressing the cable connector latch and pulling the connector from

the WWN module.

10.Hold the WWN cards by the edges and gently pull them out from the chassis.
11.Set the WWN card on a static-free surface, such as a grounding pad.

FIGURE 30

Removal and replacement of the WWN bezel (logo plate) and WWN card

Removal and Replacement Procedures

102

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Содержание DCX 8510-8

















































































































































































Результаты поиска

Содержание DCX 8510-8

Отзывы:

Похожие инструкции для DCX 8510-8

Бренды по названию

Популярные бренды

Brocade Communications Systems DCX 8510-8, Справочник по аппаратуре

Результаты поиска

Содержание DCX 8510-8

Отзывы:

Похожие инструкции для DCX 8510-8

Бренды по названию

Популярные бренды