Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 176

background image

Time and items required

The replacement procedure for an ICL cable takes less than five minutes. Only a replacement ICL
cable is required for this procedure.

Removing an ICL cable

Complete the following steps to remove a QSFP cable.

1. Grasp the rubber housing on the end of the cable and pull it straight out of the QSFP transceiver.
2. If the QSFP transceiver also needs to be replaced, remove the QSFP transceiver by rotating the

bail down and using the bail to pull the transceiver out of the connector on the blade.

3. Repeat for each cable that requires replacement.

FIGURE 37

QSFP transceiver (bail open)

1. QSFP transceiver
2. Bail

Replacing an ICL cable

Complete the following steps to replace a QSFP cable.

1. If the QSFP transceiver is being replaced, grasp the bail of the new QSFP and push the QSFP into

the connector on the blade until it is firmly seated. The QSFP is keyed to fit into the connector in
one way. The status LED initially blinks amber after installation, then displays steady amber.

2. Grasp the QSFP cable by the rubber housing and push it into the QSFP transceiver until it is firmly

seated. The cable housing is keyed to fit into the QSFP in one way.

The status LED displays steady amber until both ends of the cable are inserted and the link is
established. When the link is fully established, the LED displays steady green.

3. Repeat for each cable that requires replacement.

Once all the cables are attached, refer to the

Fabric OS Administrator's Guide

for the configuration

procedure.

Possible ICL configurations

The following figure illustrates one possible QSFP cable configuration between two DCX 8510 series
chassis. Each of two cores in one chassis should be interconnected with each of two cores in the
second chassis. This provides for inter-chassis link (ICL) trunking between chassis, ensuring
redundancy. Parallel connections between core blades are recommended.

Time and items required

110

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

«
...
108
109
110
111
112
...
»

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCX 8510-8

Бренд: TANDBERG Страницы: 187

Бренд: LaCie Страницы: 4

Express5800/R310e-E4

Бренд: NEC Страницы: 86

Sun Blade T6340

Бренд: Sun Oracle Страницы: 82

Бренд: HPE Страницы: 174

Бренд: Buffalo Страницы: 2

8676 - Eserver xSeries 335

Бренд: IBM Страницы: 172

TeraStation WSS WS5020N6

Бренд: Buffalo Страницы: 115

Бренд: Advantech Страницы: 96

BullSequana Edge nano

Бренд: Atos Страницы: 29

Бренд: EDSLab Страницы: 24

TS-h 90FU Series

Бренд: QNAP Страницы: 75

Бренд: National Instruments Страницы: 4

Бренд: G-Technology Страницы: 50

Бренд: Bosanova Страницы: 2

Бренд: DSP4YOU Страницы: 28

Бренд: Gigabyte Страницы: 136

Бренд: Gigabyte Страницы: 138

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды