Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 176

background image

The following example shows the results of the

firmwareshow

command when the firmware

versions on the two CP blades are not the same. Note the warning message at the end of the
output.

DCX_120:root> firmwareshow

Slot Name Appl Primary/Secondary Versions Status

--------------------------------------------------------------------------

6 CP0 FOS v6.4.0a STANDBY

v6.4.0a

7 CP1 FOS v7.0.0 ACTIVE *

v7.0.0

WARNING: The local CP and remote CP have different versions

of firmware, please retry firmwaredownload command.

DCX_120:root>

8. Run

haDisable

from the active CP blade to prevent failover or communication between the CP

blades during the replacement.

9. Use the

configUpload

command to upload the backbone configuration to a specified FTP server.

Enter information at the prompts.
a)

Run the

fosconfig --show

command to determine if virtual fabrics are enabled. If so, run

the

configupload -vf

command. This command uploads the Brocade DCX 8510-8 virtual

fabric data.

b)

If virtual fabrics are not enabled, run the

configupload

command. This command uploads

the Brocade DCX 8510-8 configuration.

Removing a control processor blade (CP8)

The chassis continues to operate while a CP blade is being replaced if the redundant CP blade is
active and a failover does not occur. You can prevent failover by entering the

haDisable

command.

Complete the following steps to remove a CP8 control blade.

1. Remove the chassis door.
2. Log in to the active CP as the admin user. You can use a serial cable or Telnet, Web Tools, or

Fabric Manager. Determine which CP is active using the

haShow

command or view the active LED

on the front of the CP.

3. If the faulty CP is the active CP, issue the

haFailover

command. Wait until the failover has

completed. Use the

haShow

command to verify the CPs are synchronized and the failover is

complete.

Depending on the nature of the CP failure, it is possible that the

haFailover

command may not

work. Proceed to the next step anyway.

4. Enter the

haDisable

command. This is required before physically removing and replacing a CP

blade.

5. Power off the blade by sliding the slider switch in the top ejector down to the off position. Do not

eject the blade until the power LED is off and you have completed the next two steps.

6. Disconnect all cables from the faulty (standby) CP.
7. Unscrew the thumbscrew from both ejectors using the Phillips screwdriver.
8. Lever open both ejector handles simultaneously to approximately 45 degrees and pull the CP blade

out of the chassis.

Removing a control processor blade (CP8)

86

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

«
...
84
85
86
87
88
...
»

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCX 8510-8

SUPERSERVER 6021F

Бренд: Supermicro Страницы: 116

digitalSTROM-Server

Бренд: aizo Страницы: 2

Бренд: Ganz Страницы: 5

Бренд: Patton electronics Страницы: 326

Absolute Stream

Бренд: Ideon Audio Страницы: 24

IntelliStation R Pro

Бренд: IBM Страницы: 194

Бренд: TYAN Страницы: 106

Бренд: X-media Страницы: 10

ProLiant DL580 Gen10

Бренд: HPE Страницы: 158

SUPERSERVER 6015C-M3

Бренд: Supero Страницы: 118

Anybus Communicator ABC4018

Бренд: HMS Networks Страницы: 64

ANR-C62-N1 Series

Бренд: Acrosser Technology Страницы: 57

PRIMERGY RX100 S7

Бренд: Fujitsu Страницы: 86

PRIMERGY RX1330 M1

Бренд: Fujitsu Страницы: 312

Primergy RX100 S4

Бренд: Fujitsu Страницы: 85

PRIMERGY RX1330 M1

Бренд: Fujitsu Страницы: 84

Primergy RX100 S3

Бренд: Fujitsu Страницы: 73

PRIMERGY RX100 S8

Бренд: Fujitsu Страницы: 82

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды