Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 176

background image

1. Open the ejector handles to approximately 45 degrees. Orient the CP blade so that the handles are

toward you and the flat metal side is on your left.

2. Align the flat metal side of the CP blade inside the lower and upper blade guides in the slot. Slide

the CP blade into the slot until it is firmly seated.

3. Tighten the thumbscrew inside each handle using the Phillips screwdriver.
4. Turn the CP blade on by sliding the ON/OFF switch in the top handle up, to cover the thumbscrew.
5. Verify that the power LED is green. If not, ensure that the CP blade has power and is firmly seated

and that the ejectors are in the locked position.

6. Connect the cables to the new CP blade.
7. Remain logged in to the active CP and continue to

Verifying operation of the new CP blade

on page

88.

Verifying operation of the new CP blade

To verify that boot and POST are complete on the new CP blade and that the CP blade has achieved
failover redundancy, perform the following steps.

1. Enter

slotShow

. The command output shows the new CP blade as "enabled."

If the standby CP is unresponsive, you can try unplugging the new CP blade, running

haDisable

on

the active CP blade, and plugging the new CP blade back in. At that point, you can repeat step 1 to
begin the verification process again.

2. Determine the version by entering

firmwareShow

. If the serial console on the replacement CP

blade is connected, issue the

firmwareShow

command there. More information is available through

the console.

NOTE

The DCX 8510-8 requires Fabric OS 7.0.0 or later to be recognized. If the firmware on the
replacement blade is earlier than 7.0.0 it must be brought up to the version on the active CP blade,
which must be at least 7.0.0.

3. If the firmware versions for both CP blades are the same, skip to

Completing the replacement

on

page 91.

If the firmware version on the replacement blade does not match that on the active CP blade, a
warning message appears with the results of the

firmwareshow

command. The results of the

firmwareshow

command may look similar to the following. Note the warning message at the end of

the output.

The following example is from a DCX 8510-8 chassis.

DCX_xyz:admin> firmwareshow

Slot Name Appl Primary/Secondary Versions Status

------------------------------------------------------------------------

6 CP0 FOS v7.0.0 ACTIVE

v7.0.0

7 CP1 FOS v6.3.0a STANDBY *

v6.3.0a

* Local CP

WARNING: The local CP and remote CP have different versions

of firmware, please retry firmwaredownload command.

4. You must bring the replacement blade to the same firmware level as the active blade by running the

firmwareDownload -s

command

directly on the replacement blade

to bring it up to the proper level.

The

firmwareshow

command results show which slots hold the active and standby (replacement)

CP blades.

If you are using an FTP server to download the firmware, skip to

Downloading firmware from an

Verifying operation of the new CP blade

88

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

«
...
86
87
88
89
90
...
»

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCX 8510-8

Бренд: Acano Страницы: 17

Бренд: Lantronix Страницы: 10

Бренд: Lantronix Страницы: 17

Бренд: Lantronix Страницы: 109

Бренд: Lantronix Страницы: 24

Бренд: Lantronix Страницы: 29

Бренд: Lantronix Страницы: 2

Link Manager 4010-43

Бренд: Point Six Страницы: 131

Бренд: Synology Страницы: 15

Flex System x240 Compute Node

Бренд: IBM Страницы: 28

Бренд: Oki Страницы: 2

SimpliVity 2600 Gen10

Бренд: HPE Страницы: 37

Бренд: Patton electronics Страницы: 121

Бренд: AXIOMTEK Страницы: 55

SuperServer 5037C-i

Бренд: Supermicro Страницы: 88

System x3650 M4 BD Type 5466

Бренд: IBM Страницы: 786

4 Ch Video Sever

Бренд: Video Server Страницы: 34

SuperServer 1029U-T Series

Бренд: Supermicro Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды