manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Справочник по аппаратуре

Поделиться
Скачать
Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 65

Port and application blade LED descriptions (Continued)

TABLE 5   

LED purpose

Color

Status

Recommended action

Steady amber

Port is receiving light or
signal carrier, but it is not
online yet.

Reset the port from the
workstation using the

portEnable

 or

portCfgPersistentEnable

command.

Slow-flashing amber (on 2
seconds, then off 2
seconds)

Port is disabled due to
diagnostic tests or

portDisable

 or

portCfgPersistentEnable

command.

Reset the port from the
workstation using the

portEnable

 or

portCfgPersistentEnable

command.

Fast-flashing amber (on
1/2 second, then off 1/2
second)

Transceiver or port is
faulty.

Change the transceiver or
reset the switch from the
workstation.

Alternating green/amber

Port is bypassed.

Reset the port from the
workstation using the

portEnable

 or

portCfgPersistentEnable

command.

GbE Port Status (FX8-24)
- both 1 GbE and 10 GbE
ports

No light (LED is off)

Port has no incoming
power, or there is no light
or signal carrier detected.

Verify that the power LED
is on, check the
transceiver and cable.

Steady green

Port is online but has no
traffic.

No action required.

Slow-flashing green (on 1
second, then off 1 second)

Beacon. Used to identify
specific ports.

No action required.

Flickering green

Port is online, with traffic
flowing through port.

No action required.

Fast-flashing amber (on
1/4 second, then off 1/4
second)

Transceiver or port is
faulty.

Change the transceiver or
reset the switch from the
workstation.

Determining the status of a control processor blade (CP8)

Complete the following steps to determine the status of a control processor blade (CP8)

1. Check the LED indicators on the CP blade. The LED patterns may temporarily change during POST

and other diagnostic tests. For information about how to interpret the LED patterns, refer to the
following table.

2. Check the port blade status by entering 

slotShow

 and 

haShow

.

Determining the status of a control processor blade (CP8)

Brocade DCX 8510-8 Backbone Hardware Reference Manual

65

53-1002180-08

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды