Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 104

Страница: 104 / 176

Blade

Transceiver

Auto-negotiate/Fixed

Speeds supported(xGbps)

FC8-64

mSFP

Auto negotiate

2, 4, and 8.

FC16-32 and FC16-48

SFP+

Auto negotiate

2, 4, 8, and 16

FC16-32 and FC16-48

10-Gbps SFP+

Fixed

FCOE10-24

10-GbE SFP+ (only
optical)

Fixed

FC16-64

QSFP

Auto negotiate

4, 8, and 16. However, all the four
ports within a quad-SFP should be
of the same speed.

CR16-4/8

QSFP

Fixed

Time Required

The replacement procedure for a transceiver takes less than five minutes.

Items Required

• Replacement mSFP, SFP, SFP+, or XFP
• Optical transceiver extraction tool (for SFP, SFP+, and XFP transceivers)

Most Brocade switches and backbones come with a transceiver extraction tool and holster. The
extraction tool is designed to remove transceivers from switches and blades where the space is
limited.

FIGURE 31

Optical transceiver (SFP+) extraction tool

Removing an SFP+ transceiver

Complete the following steps to remove an SFP+ transceiver.

1. Remove any cables that are inserted into the transceiver. Use the extraction tool to open the cable

latching mechanism.

2. Using the hooked end of the tool, pull the bail (wire handle) away from its pivot point and out, sliding

the transceiver out of the switch or blade.

Time Required

104

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Содержание DCX 8510-8

















































































































































































Результаты поиска

Содержание DCX 8510-8

Отзывы:

Похожие инструкции для DCX 8510-8

Бренды по названию

Популярные бренды

Brocade Communications Systems DCX 8510-8, Справочник по аппаратуре

Результаты поиска

Содержание DCX 8510-8

Отзывы:

Похожие инструкции для DCX 8510-8

Бренды по названию

Популярные бренды