Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 176

background image

Replacing the WWN card and WWN bezel (logo plate)

Complete the following steps to replace the bezel and the WWN cards.

Follow electrostatic discharge (ESD) precautions. Wear a wrist grounding strap connected to chassis
ground (if the Brocade DCX 8510-4 is plugged in) or a bench ground.

DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.

1. Ensure that the chassis is still powered off. If not, power down the entire chassis.
2. Unpack the two new WWN cards and save the packaging for the faulty WWN cards.

The WWN cards and cables are labeled #1 for the left slot and #2 for the right slot.

3. Hold each card by the edges and insert the WWN cable onto the WWN module until the cables are

fully seated.

4. Hold each card by the edges and slide the card into the chassis. Use the Phillips screwdriver and the

screws to secure the WWN card to the chassis.

5. Power on the chassis and wait for five minutes for the chassis to boot.
6. Verify that the WWN card is correctly connected by checking the LEDs on the WWN card to see if

they reflect the status of the components.

NOTE

The LEDs may take up to two minutes after WWN card installation to begin functioning.

7. Install the WWN bezel. Orient the bezel on the chassis. Insert and tighten the screws.
8. Verify the new card settings by running the following commands and comparing the output with the

original

supportsave

data:

1.

licenseidshow

2.

ipaddrshow

3.

switchname

4.

chassisname

5.

wwncardshow ipdata

6.

chassisshow

(look at the WWN and Chassis information at the bottom)

7.

ficonshow switchrnid

9. Run the

switchcfgpersistentenable

command to persistently enable each logical switch, that were

disabled before removing the WWN cards:

switch:FID128:root> switchcfgpersistentenable

Switch's persistent state set to 'enabled'

10.Pack the faulty WWN cards in the packaging provided with the new cards, and return them to

Brocade Support for failure analysis (FA).

Transceiver removal and replacement

Use the procedures in this section to remove and replace various types of transceivers supported.

Blade

Transceiver

Auto-negotiate/Fixed

Speeds supported(xGbps)

FC8-32E and FC8-48E

SFP+

Auto negotiate

2, 4, and 8.

Replacing the WWN card and WWN bezel (logo plate)

Brocade DCX 8510-8 Backbone Hardware Reference Manual

103

53-1002180-08

«
...
101
102
103
104
105
...
»

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCX 8510-8

Бренд: Panasonic Страницы: 31

x3655 - System - 7985

Бренд: IBM Страницы: 118

SuperServer 5013C-MT

Бренд: Supero Страницы: 98

Бренд: TYAN Страницы: 170

AMD Opteron LS20 Type 8850

Бренд: IBM Страницы: 68

SUPERO SuperServer 1018L-MP

Бренд: Supermicro Страницы: 104

Bull Escala E5-700

Бренд: IBM Страницы: 116

Бренд: Xyplex Страницы: 58

Бренд: Cable-Tronix Страницы: 33

SUPERSERVER 5019S-M

Бренд: Supermicro Страницы: 65

Бренд: Goonas Страницы: 13

totalstorage fastt100

Бренд: IBM Страницы: 160

Firepower Management Centers

Бренд: Cisco Страницы: 20

Бренд: Cisco Страницы: 34

MCS-7825-H1-IPC1

Бренд: Cisco Страницы: 54

Бренд: Cisco Страницы: 62

Бренд: Cisco Страницы: 10

KIN-UCSM5-1RU-K9

Бренд: Cisco Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды