manualshive.com logo in svg

Brink Air Comfort, Правила установки

Поделиться
Скачать
Brink Air Comfort Скачать руководство пользователя страница 40

11 Electrical connections

accessories

11.1 Connecting external connectors Air Comfort

1

2

3

4

5

6

7

8

9

1

2

1

2

1

2

1.

External contacts - These contacts are used to connect external devices onto the appliance.

▪

Position 1 and 2 - This is a switch contact for the cooling. The cooling is activated if contact is made.

▪

Position 3 and 4 - This is a switch contact for an external fault. The system ventilator of the appliance is

switched off in the event of a fault 

E107

, see 

Display codes

 (op pagina 35).

▪

Position 5 and 6 - This relay is activated by the frost protection, for example through introducing an external

pump.

▪

Position 7 and 8 - This relay is activated by cooling, for example through connecting an interface for the

cooling.

2.

24V power - maximum 4.5 VA (black).

3.

eBus communication - the connection is polarity sensitive (green).

4.

eBus communication - the connection is polarity sensitive (green).

5.

Connection 4

‑

position switch.

Air Comfort 614788-B

Содержание Air Comfort



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды