Brink Air Comfort Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 50

Brink Air Comfort Скачать руководство пользователя страница 28

6.2 Operating mode

The operating mode is shown on the display by means of 4 different values:

▪

The status of the system ventilator (zie

System ventilator status

op pagina 28)

▪

The air discharge temperature

▪

A notification message (zie

Notification message for operating mode

▪

If applicable, a fault symbo

Trouble shooting

1

2

3

4

1. System ventilator status
2. Air discharge temperature display
3. Notification message
4. Fault symbol

6.2.1 System ventilator status

The status of the system ventilator is shown on the left-hand side of the display with a ventilator symbol and a

number, see

Programme choice

(op pagina 14).

The ventilator symbol is only shown whilst the system ventilator is in operation.

6.2.2 Notification message for operating mode

If applicable, a notification message is shown top left on the display.
The

FILTER

notification also takes priority over all other messages.

The following messages can be shown on the display:

Notification message

Description

FILTER

The filter must be cleaned or replaced, see Clean filter (zie

Cleaning filter

op pagina 37).

PR1

Fixed programme

(op pagina 16) has been set.

PR2

(op pagina 17) has been set.

Air Comfort 614788-B

«
...
26
27
28
29
30
...
»

Содержание Air Comfort



















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды