manualshive.com logo in svg

Brink Air Comfort, Правила установки

Поделиться
Скачать
Brink Air Comfort Скачать руководство пользователя страница 30

6.4 Read out menu

Use the read out menu to retrieve current measurement values

Measurement-

value

Description

Unit

1

Current discharge temperature

ºC

2

Current water temperature in the heat exchanger

ºC

3

Current speed of the system ventilator

%

4

Number of revs of system ventilator

RPM

5

Status of frost control:

- ON

: frost control active

- OFF

: frost control not active

-

6

Readout value CO

2

 sensor A

PPM

7

Readout value CO

2

 sensor B

PPM

8

Readout value CO

2

 sensor C

PPM

9

Readout value CO

2

 sensor D

PPM

Reading out measurement values:

1 Press 

[Menu]

2 Press 

[+]

 or 

[-]

 to navigate to the readout

menu 

READ

.

3 Press 

[Menu]

 to activate the readout menu.

4 Press 

[+]

 or 

[-]

 to navigate through the

measurement values in the readout menu.

5 Press 

[R]

 to return to the menu choice.

6 Press 

[R]

 again to return to the operating mode.

Air Comfort 614788-B

Содержание Air Comfort



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды