Brink Air Comfort Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 50

Brink Air Comfort Скачать руководство пользователя страница 33

7.3.1 Connecting several Air Comfort appliances

A maximum of 4 Air Comfort appliances can be connected to one another. Use parameter

26

to set a unique

identification number for each appliance, see the

(op pagina 47).

If the Air Comfort appliances are applied in combination with a heat recovery unit, this also must have a unique

identification number. This can be set with parameter

27

.

7.3.2 Connecting Air Comfort appliance with Renovent Excellent appliance

If a Renovent Excellent heat recovery unit is connected to the Air Comfort appliance or a series of a maximum of

4 Air Comfort appliances, then the Renovent Excellent type must be set with parameter

27

(op pagina 47).

This parameter must be set on every Air Comfort appliance.

7.4 Factory settings

Press

[+]

and

[-]

for 10 seconds at the same time in order to return all settings to the factory settings.

Only the filter setting is not returned to the factory settings.

After returning to the factory settings, the display shows all symbols for 3 seconds. After that, the appliance

returns automatically to the operating mode.

Air Comfort 614788-B

Brink / 33

«
...
31
32
33
34
35
...
»

Содержание Air Comfort



















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды