manualshive.com logo in svg

Brink Air Comfort, Правила установки

Поделиться
Скачать
Brink Air Comfort Скачать руководство пользователя страница 24

1. Appliance
2. Funnel
3. Anti-smell valve
4. Connecting pipe
5. Standpipe

5.3.2.2 Condensation discharge when using Renovent Excellent

Use the siphon set with article number 217052 for connecting the Renovent Excellent heat recovery unit if this is installed

onto a Air Comfort appliance.

Connect the condensation discharge of the heat recovery unit.

1. Remove the protective cover and front panel of the Air

Comfort and of the Renovent Excellent.

2. Connect the siphon (2) of the siphon set to the Renovent

Excellent (1), see also the installation instructions of

the Renovent Excellent heat recovery unit.

3. Feed the condensation discharge tube through the tulle

underneath the control panel.

4. Place the front covers back on the Air Comfort

5.4 Connecting ducts

Connect the warm air duct onto the coupling ring of the air outlet:

1. If necessary, install a regulating valve in the air outlet.
2. Insulate the warm air duct, the grating and the possible outside air duct.
3. Apply a moisture repellent layer over the insulation material in order to prevent condensation forming.

If the coupling ring of the air outlet is not on the correct side of the appliance before installation, use can be

made of an air distributing box (discharge module).

Air Comfort 614788-B

Содержание Air Comfort



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды