Bowflex BXT116 Скачать руководство пользователя

Страница: 60 / 179

Lift Shock

The following images show the machine upright,

and not fully resting on its side. The machine must

be on its side to safely complete the following

steps.

10. Using a 10mm wrench, loosen the locking nut for the Release Cable

(indicated by arrow).

11. Using a 14mm wrench, disconnect the securing nut and remove the

Release Cable Assembly from the Lift Shock.

12. Using a #2 Phillips screwdriver, remove the indicated screw and the

Deck Release Handle Assembly.

13. Route the new cable through the frame, and attach the new Deck

Release Handle Assembly with a #2 Phillips screwdriver.

Spring

Note:

Make sure the spring that connects to the Deck Release Handle is

properly oriented during re-assembly.

Содержание BXT116




















































































































































































Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды

Bowflex BXT116, Руководство по обслуживанию

Результаты поиска

Содержание BXT116

Отзывы:

Похожие инструкции для BXT116

Бренды по названию

Популярные бренды